Rear Window Gasket
p/n: 60-0121-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has the divider bars molded directly into it. It has properly molded corners to precisely conform to the glass and has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket
p/n: 20-0479-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0268-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0152-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0284-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0609-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0302-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 70-1758-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The gasket has the divider bars molded directly into it and has molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket Set
p/n: 60-0082-83
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. Both strips comes in a ninety inch (90") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Rear Window Gasket Set
p/n: 40-0445-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and the locking strip holds it tight for a precise, factory fit.
Rear Window Gasket Set
p/n: 20-2617-83
This Rear Window Gasket Set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 40-0473-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and the locking strip holds it tight for a precise, factory fit.
Rear Window Gasket Set
p/n: 70-2594-81
This Rear Window Gasket Set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 20-0483-81
This Rear Window Gasket Set contains the gaskets that mount around the two (2) back windows on the rear barn style cargo doors. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 70-1819-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The gasket has the divider bars molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket Set
p/n: 40-0462-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and the locking strip holds it tight for a precise, factory fit.
Rear Window Gasket Set
p/n: 60-0380-81
This Rear Window Gasket Set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 70-3472-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The gasket has the divider bars molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Red Brake and Clutch Pedal Pad
p/n: 30-0114-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0114-22.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Rigid Run Channels
p/n: 30-0023-57
This Rigid Run Channel pair for the division bar is un-beaded, steel core, plush lined, and cloth covered. Available as 28" pair.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Run Channel Retaining Clip
p/n: 60-0374-58
This Run Channel Retaining Clip is designed from the original part for an authentic fit, finish and function. Clip fits at the end of door window run channel. Tempered spring steel.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Running Board To Body Filler
p/n: 70-1116-45
This Running Board To Body Filler is extruded from dense rubber for a durable and proper seal. Sold as a forty (40") inch pair of filler strips.
Running Board To Body Filler
p/n: 70-1117-45
This Running Board To Body Filler is extruded from dense rubber for a durable and proper seal. Sold as a sixty-four (64") inch pair of filler strips.
Sash Channel Weatherstrip
p/n: 60-0690-58
Weatherstrip, sash channel. Correct extrusion. Two (2) strips cut twenty five and one half (25-1/2) inches long.
Shift Lever Bushing
p/n: 70-2026-26
Bushing, lower shift levers and adjustable eye. Includes metal tube bearing. Used on transmission shifter rods.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Shift Linkage Repair Set
p/n: 20-2460-26
This column Shift Linkage Repair set is designed from the original parts for superior fitment and function. This repair set replaces worn or missing bushings at the four linkage points in the column shift mechanism.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
Shock Absorber Bushing
p/n: 70-0547-32
This Shock Absorber Bushing is manufactured with high-quality EPDM rubber to OEM specifications. The bushing is the double cone style. Designed from original part to ensure proper fit.
Shock Absorber Grommet
p/n: 60-0235-33
This Shock Absorber Grommet is fully molded and designed from the original part for superior fitment and durability. The grommet the plain cylinder type with flat ends for shock absorber mounting.
Shock Absorber Link Arm Bushing
p/n: 60-0216-33
This Shock Absorber Link Arm Bushing is designed from the original part for superior fitment, finish and function. This bushing is for double acting shock absorber arm links.
Shock Absorber or Track Bar Bushing
p/n: 20-2476-33
This Shock Absorber or Track Bar Bushing is designed from the original part for superior fitment and function. These bushes are used on tubular-style shock absorbers and also on stabilizer track bar(s).
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Side Roof Rail Weatherstrip
p/n: 70-0155-65
Weatherstrip, convertible roof rail. Available by the foot.
Side Window Bumper
p/n: 70-3428-62
Pad, side window inside anti-rattle. Three eights (3/8) inch by one (1) inch for three sixteenths (3/16) inch by three fourths (3/4) inch slot in sheet metal. Six (6) required per truck
Side Window Leading Edge
p/n: 30-0475-57
Weatherstrip, quarter window leading edge.Length: 12.125 inches. Width: .8125 inches.
Side Window Leading Edge
p/n: 20-2604-80
Side window vertical leading edge weatherstrip. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.