Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Division bar grommet
p/n: 70-3135-62
Grommet, rear door vent divider post. Upper and lower, right and left. 4 piece set.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Door Bumper
p/n: 60-0334-71
Bumper, back door check link above door. Dovetail base fits check arm.Length: 1.0 inches. Width: 1.0 inches. Height: .625 inches.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Door Check Arm Bumper
p/n: 20-1639-70
This Door Check Arm Bumper is designed from the original part for superior fitment and function. This rubber with arm slot bumper mounts on the door check arm. Works to cushion the door swing.
Door Conduit
p/n: 70-0828-21
Conduit, hydraulic line & power window wire. Front doors only. 2 pieces cut nine and one half (9-1/2) inches.Length: 9.50 inches. Height: 1.50 inches.
Door Edge Weatherstrips
p/n: 60-0030-73
This Door Edge Weatherstrip pair is designed from the original part for superior fitment and sealing. These primary door weatherstrips mount directly to the vehicle body.
Door Garnish Molding Pad
p/n: 30-0435-71
Support, door garnish molding. Up to twenty (20) required per car.Width: .875 inches. Height: 1.0 inches.
Door Glass Run Channel Set
p/n: 20-2537-58
Door Glass Run Channel Set - Includes front door side window division bar, run channel, and window felts. Fabric covered division bar and stainless steel window felts. This set does two (2) doors.
Door handle gasket
p/n: 20-2584-69
Pads, outside door handle. Set includes four (4) pieces for two (2) handles.
Door handle gasket
p/n: 20-2587-69
Pads, outside door handle. Enough for two (2) handles. Four (4) piece set.
Door Handle Gasket Set
p/n: 60-0673-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door Handle Gasket Set
p/n: 50-0322-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door Handle Gasket Set
p/n: 70-0572-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Door Handle Gaskets
p/n: 20-0478-69
This two (2) piece Outside Door Handle Gasket pair is designed from the original part for superior fitment and seal. Gaskets have a proper raised edge to center the handle on so it fits correctly.
Door Handle Mounting Pad
p/n: 20-0577-86
Outside Door Handle Mounting Pad - Designed from an original part so it fits correctly.
Door Jamb Bumper
p/n: 20-2109-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
Door Lock Bumper
p/n: 34-0484-71
This Door Lock Bumper is made from high-quality EPDM dense rubber to provide excellent durability. Designed for applications such as the upper door lock post.
Door opening step grommet
p/n: 40-0125-49
Grommet, door sill mat retainer at lower door opening. All sill plates with metal stud retainer. (Included in our #40-0542-49 set).
Door opening step pad
p/n: 40-0541-49
Mats, door sill opening, on body. Clip type. For stud-type see our #40-0542-49) mat includes retaining grommets (40-0125-49).
Door Opening Step Pad
p/n: 40-0542-49
This Door Opening Step Pad set installs on the door sill opening, on the body. Designed with the original pattern and metal core.
Door opening step pad
p/n: 40-0389-49
Mats, door sill opening, on body. Made without metal core (copied from authentic rubber only original). Molded-in carrot retainers.
Door opening step pad
p/n: 70-2622-49
Mat, door opening, on body. Front doors. For rear doors see our #70-2623-49. Excellent craftsmanship with authentic metal core with studs like original.
Door opening step pad
p/n: 70-2623-49
Mat, door opening, on body. Rear doors. For front doors see our #70-2622-49. Excellent craftsmanship with authentic metal core with studs like original.
Door Vent Window Foot
p/n: 20-2556-62
This Door Vent Window Foot installs at the base of the front door vent window frame. Sold as a pair.
Door Weatherstrip
p/n: 60-0250-73
Weatherstrip, door bottom and corners, molded right and left. Overall length forty and three fourths (40-3/4) inch per door.
Door Weatherstrip
p/n: 70-0738-73
Weatherstrip, front door. Includes molded end and extruded strip from inner end to bottom edge. With brass screw retainer as original.Length: 98.0 inches.
Door Weatherstrip
p/n: 60-0313-73
Weatherstrip, door bottom. Retained by metal strip, black only. Each strip approximately thirty two and one half (32-1/2) inches long.
Door Weatherstrip
p/n: 70-0668-73
Weatherstrip, body hinge pillar to door, bellows type of seal. One thirty seconds (1/32) inch thick. Die cut to exact outline.Length: 29.50 inches.
Door weatherstrip
p/n: 60-0476-73
Weatherstrip, auxiliary, front door opening. Right and left, at beltline on body hinge post, above upper hinge. Metal core, as original, with screw holes.
Door weatherstrip
p/n: 70-0948-73
Weatherstrip, front door bottom. High quality weatherstrip with molded right and left hand ends.
Door Weatherstrip
p/n: 50-0219-73
This Door Weatherstrip is made of a high-quality sponge extrusion to original configuration. This weatherstrip is for the front door opening, lower front body hinge pillar.
Door weatherstrip
p/n: 70-0530-73
Weatherstrip, front door. Upper on edge of door or body opening. Molded ends, right and left.
Door weatherstrip
p/n: 40-0340-73
Weatherstrip, door, body hinge pillar to front quarter panel, right and left. Copy of original (except no steel core). Retained by rubber tabs for screws.
Door Weatherstrip
p/n: 60-0664-73
Weatherstrip, auxiliary on body lock pillar. Correct extrusion cut thirty (30) inches long.
Door Weatherstrip
p/n: 30-0473-73
Weatherstrip, rear door hinge on center pillar.Length: 32.0 inches.
Door Weatherstrip
p/n: 60-0324-73
Weatherstrip, front door opening. Right and left, hinge pillar at beltline. Constructed of soft rubber.Length: 12.0 inches.
Door Weatherstrip
p/n: 40-0168-73
This Door Weatherstrip is generally used as a hinge post on door or body opening, in area around hinges where irregular cross section is required. Available by the foot.
Door Weatherstrip
p/n: 60-0517-73
Weatherstrip, front door hinge pillar at beltline. Fourteen and one half (14-1/2) inches long, molded right and left.Length: 13.75 inches.
Door Weatherstrip
p/n: 30-0186-73
Weatherstrip, front door to fender (hinge pillar). Soft, solid rubber construction with tabs for all screws, but without metal core.
Door Weatherstrip Hinge Pillar
p/n: 50-0268-73
Weatherstrip, body hinge pillar to door, bellows type seal.
Door Weatherstrip Set
p/n: 20-0499-72
This Door Weatherstrip Set is designed from the original parts for superior fitment and seal. These primary door weatherstrips mount (glue-on) directly to the left and right doors sealing the full perimeter of the doors against the vehicle body when the door is closed.
Door Weatherstrips - Lower
p/n: 60-0078-73
This Lower Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Heavy type with original ribbing and retainer lip.
Drag Link End Repair Set
p/n: 20-0506-32
This Drag Link End Repair set is designed from the original parts for superior fit and function. This repair set will help your worn and aged steering connections to be once again as tight as the factory made them and help to make steering your classic truck easy again.
Electrical Terminal Boot
p/n: 30-0279-41
This Electrical Terminal Boot is designed from the original part for superior fitment and seal. This boot works to cover and protect electrical terminal connections.
Emergency Brake Cable Grommet
p/n: 20-2438-20
This Emergency Brake Cable Grommet is used to run the emergency brake cable through the firewall. Designed from the original part for superior fit and seal.
Engine Mount
p/n: 20-1978-11
This Engine Mount is designed from the original part for superior fitment and function. This engine mount works to absorb and isolate engine and driveline vibrations. The set services one mount. 1937-1941 require four (4) sets for both Front and Rear. 1942-1948 require two (2) sets.
Engine Mount Bolt
p/n: 20-0309-11
This Engine Mount Bolt can be used for the front or rear. Hex head bolt drilled for cotter key.
Engine Mount Pad
p/n: 30-0238-11
This Engine Mount Pad pair is used as a support cushion at the timing gear cover. Correct design and rubber compound. Sold only in pairs. One (1) pair required per car.
Engine Mount Pad
p/n: 70-2577-11
This Engine Mount Pad pair is used as a lower support cushion. Correct design and rubber compound. Sold as a pair.
Engine Mount Pad
p/n: 30-0267-11
This Engine Mount Pad pair is used as a support insulator at the timing gear cover. Correct design and rubber compound.
Engine Mount Service - Revulcanization Only
p/n: 40-0411-11
This Engine Mount Revulcanization Service Only is designed to restore your original rear upper engine support insulators to a like new condition. The Revulcanization Service requires your original cores.
Engine Mount Service – Revulcanization Only
p/n: 30-0415-11
This Revulcanization Service Only is designed to restore your Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 60-0296-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 40-0410-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 27-0039-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 25-0072-11
This Revulcanization Service Only is designed to restore your Right and Left Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 60-0241-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 27-0046-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 10-0135-11
This Revulcanization Service Only is designed to restore your Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 70-0528-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 27-0044-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 70-0674-11
This Revulcanization Service Only is designed to restore your Rear Engine Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 25-0062-11
This Revulcanization Service Only is designed to restore your Front Upper Engine Mount at Crossmember to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 70-1283-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.