Door edge weatherstrip (1951-1st type). This part is the primary door to body weatherstrip. This kit includes the seals for the top and sides, the bottom of the door with molded ends and the bellows seal. Adhesive is not included in the kit.
This rear window gasket mounts around the full perimeter of the back glass and has the divider bars molded directly into it. It has properly molded corners to precisely conform to the glass and has the slot to accommodate the outer edge's decorative molding.
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. This seal has molded sections for the wiper transmissions and the slot to accommodate the outer molding.
This ten (10) piece Window Felt and Run Channel set includes the inner and outer window felts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Door edge weatherstrip. This part is the primary door to body weatherstrip. Includes the lower hinge pillar weatherstrip.
Front motor mount cushion. Revulcanization service only. Send in cores and allow three weeks for service. Include inner core
Scoop, air intake at front end sheet metal.
Weatherstrip, front door bottom. High quality weatherstrip with molded right and left hand ends.
Weatherstrip, front door. Includes molded end and extruded strip from inner end to bottom edge. With brass screw retainer as original.Length: 98.0 inches.
Engine harmonic balancer. Revulcanization service only. Send in your old, rebuildable balancer and pulley assembly.
This 1948-1959 Cadillac Master Parts List - Two (2) Volume set licensed Detroit Iron reprint provides the most comprehensive repair information in paper format. This OEM PARTS manual reproduction provides detailed original part numbers, part assembly diagrams / illustrations and part textual details for all vehicle subsystems.
Cushion, motor support, rear on transmission to cross member. Revulcanization service only.
Cushion support, motor, rear on transmission to cross member. Revulcanization service only. Similar to #70-0674-11.Length: 3.75 inches. Width: 2.25 inches.
This Trunk Weatherstrip set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Kit, front stabilizer bar link assembly replacement. Twenty two (22) piece set for both sides of one (1) car. Hex head bolt. 3/8"-16nc x 8-7/8" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Bumpers, front spring. Lower arm, original copy, integral molded plate and stud, three eighths (3/8) inch standard thread, for installing.
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Weatherstrip, body hinge pillar to door, bellows type of seal. One thirty seconds (1/32) inch thick. Die cut to exact outline.Length: 29.50 inches.
Gasket set, taillight assembly. Four (4) piece set for lens and housing, right and left.
Fender Skirt Edge Seal pair. Length: 60.0 inches. Width: 5/8 inches.
Weatherstrip, rear door lower hinge pillar.Length: 16.0 inches.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Bumper, front spring, upper arm (on frame).
Pad, accelerator pedal. Brown rubber. For black see our #70-0208-40. Made to slip over old metal core after removing old rubber.
Bottoming pads, rear axle. Rubber block mounts by bracket to rear axle tube.
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Seal, fenderskirt edge. Good quality and workmanship, see sketch for comparison. Ten (10) foot strip.Length: 120.0 inches. Width: .1875 inches.
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Pads, brake and clutch pedals. Brown rubber. For black see our #70-0176-22.Color:brown Length: 3.8125 inches.
Bushings, front stabilizer bar. Fully molded rubber. One and five eighths inch (1 5/8") length by one and seven sixteenths inch (1 7/16') width by three fourths inch (3/4") inside hole diameter by one and eleven sixteenths inch (1 11/16") height.
Pad, accelerator pedal. Black rubber. For brown see our #70-0208-89. Made to slip over old metal core after removing old rubber.Length: 8.25 inches.
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
This Rear Bumper Stone Deflector is a bulb type seal. Made of high-quality EPDM dense rubber and designed from original parts for superior fitment and seal. Twelve (12) foot strip.
Seat, mounting bracket for back-up light.
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Pads, brake and clutch pedals. Black rubber. For brown see our #70-0176-89.
Gasket, fog light body to ring or bezel.
Gasket, fog light lens to reflector.
This Front Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs.