Search Results
Windshield Gasket
p/n: 70-0512-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has molded sections for the wiper transmissions and the slot to accommodate the outer edge's decorative molding.
Side Window Run Channel Kit
p/n: 90-0141-58
This ten (10) piece kit includes the inner and outer windowfelts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Rear Door weatherstrip
p/n: 90-0119-72
Door edge weatherstrip. This part is the primary door to body weatherstrip. Includes the lower hinge pillar weatherstrip.
Front Door Vent Window Set
p/n: 90-0458-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Door weatherstrip
p/n: 70-0948-73
Weatherstrip, front door bottom. High quality weatherstrip with molded right and left hand ends.
Front Door Vent Window Weatherstrips
p/n: 38-0046-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Door weatherstrip
p/n: 70-0550-73
Weatherstrip, door bottom (1951-2nd type). Molded left and right, overall length forty (40) inches.
Door weatherstrip
p/n: 70-0738-73
Weatherstrip, front door. Includes molded end and extruded strip from inner end to bottom edge. With brass screw retainer as original.Length: 98.0 inches.
Hood to cowl weatherstrip
p/n: 50-0436-43
Weatherstrip, hood to cowl. 31" long. Note: compare to #50-0167-43 hood to cowl sold separately.
Axle rebound pad
p/n: 50-0371-35
Bumper, rear axle. Revulcanization service only.Height: 3.5 inches.
Taillight wiring boot and hose
p/n: 50-0420-15
Boot and hose, taillight wiring. Four (4) piece set includes end covers.Width: 16.375 inches.
Hood to cowl weatherstrip
p/n: 50-0167-43
Weatherstrip, hood to cowl. 56 1/2 " long. Note: compare to #50-0436-43 hood to cowl sold separately.
Motor mount service
p/n: 50-0297-11
Motor mount, front. Revulcanization service only.Qty Required:2 Length: 3.375 inches. Width: 2.625 inches. Height: 1.25 inches.
Transmission mount service
p/n: 50-0264-25
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Transmission mount service
p/n: 50-0263-25
Support, transmission (insulator). Revulcanization service only. See also our #50-0262-25, many models use both.Length: 5.0 inches. Width: 1.875 inches.
Transmission mount service
p/n: 50-0262-25
Pad, transmission mounting, thrust. Revulcanization service only. One (1) per car required. See also our #50-0263-25. Many models use both.Length: 7.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Door weatherstrip hinge pillar
p/n: 50-0268-73
Weatherstrip, body hinge pillar to door, bellows type seal.
Rigid Run Channel
p/n: 70-0536-58
Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top. Available in 29" pairs.
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Flexible Run Channel
p/n: 70-1239-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Beltline Weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Vent division bar weatherstrip
p/n: 60-0569-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Headlight Door To Lens Seal
p/n: 70-0389-14
Headlight door to lens seal. Molded without wire. Single lip type for sealed beams.
Front stabilizer bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber. One and one half inch (1 1/2") length by one and one half inch (1 1/2") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half in
Brown brake and clutch pad
p/n: 50-0054-89
Pad, brake and clutch pedal. Brown rubber. For black see our part #50-0054-22. Perfect copy, fine detail.Color:brown Width: 3.125 inches.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 6ft lengths.
Door weatherstrip
p/n: 50-0219-73
Weatherstrip, front door opening, front body hinge pillar, lower. Extruded sponge to original configuration. Two (2) required per car.Width: .875 inches.
Front suspension bumper
p/n: 50-0092-32
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Side Window Sash Channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Rigid Run Channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Brake and clutch shank seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Brake and clutch pedal pad
p/n: 50-0054-22
Pad, brake and clutch pedal. Black rubber. For brown see our part #50-0054-89. Perfect copy, fine detail.Width: 3.125 inches. Height: 2.125 inches.
Front coil spring pad
p/n: 50-0358-35
Insulators, front coil spring. Fabric reinforced rubber as original.
Heater control valve seal
p/n: 50-0356-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water. For all except right-hand drive.
Body mounting pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar. One and seven eighths inch (1 7/8") outside diameter by one and one eighths inch (1 1/8") locating collar outside diameter by three fourths inch (3/4") locating collar inside diame
Taillight mounting pad
p/n: 50-0410-15
Pad, taillight to fender.Width: 7.25 inches. Height: 4.0 inches.
Taillight lens gasket
p/n: 50-0411-15
Gasket, taillight lens. Die cut three sixteenths (3/16) inch sponge rubber as original.Width: 6.25 inches. Height: 3.25 inches.