Door edge weatherstrip. This part is the primary door to body weatherstrip.
Convertible roof rail weatherstrip. This part fits on the folding roof of the vehicle and seals the side window when the window is fully raised. Fully molded with metal core. Eight (8) piece kit.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has molded sections for the wiper transmissions and the slot to accommodate the outer edge's decorative molding.
This front door vent window weatherstrip kit is a six (6) piece set that contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front motor mount cushion. Revulcanization service only. Send in cores and allow three weeks for service. Include inner core
This front door vent window weatherstrip set contains the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
Scoop, air intake at front end sheet metal.
Weatherstrip, front door lock pillar. Ready to install with molded ends.Length: 36.0 inches. Width: .625 inches. Height: .625 inches.
Weatherstrip, door bottom (1951-2nd type). Molded left and right, overall length forty (40) inches.
Weatherstrip, front door. Upper on edge of door or body opening. Molded ends, right and left.
Engine harmonic balancer. Revulcanization service only. Send in your old, rebuildable balancer and pulley assembly.
This 1948-1959 Cadillac Master Parts List - Two (2) Volume set licensed Detroit Iron reprint provides the most comprehensive repair information in paper format. This OEM PARTS manual reproduction provides detailed original part numbers, part assembly diagrams / illustrations and part textual details for all vehicle subsystems. This information set is a high-quality reproduction of the exact parts manual originally published for use by Cadillac dealer mechanics.
Cushion, motor support, rear on transmission to cross member. Revulcanization service only.
Cushion support, motor, rear on transmission to cross member. Revulcanization service only. Similar to #70-0674-11.Length: 3.75 inches. Width: 2.25 inches.
This trunk weatherstrip set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Kit, front stabilizer bar link assembly replacement. Twenty two (22) piece set for both sides of one (1) car. Hex head bolt. 3/8"-16nc x 8-7/8" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Bumpers, front spring. Lower arm, original copy, integral molded plate and stud, three eighths (3/8) inch standard thread, for installing.
Gasket set, rear and back up light installation. Sold in ten (10) piece set only. (A) Gasket, rear light body. twenty two (22) inches overall.
Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top. Available in 29" pairs.
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Weatherstrip, body hinge pillar to door, bellows type of seal. One thirty seconds (1/32) inch thick. Die cut to exact outline.Length: 29.50 inches.
Bumper, on folding top female hinge, for folding post, when top is retracted, right and left, brass core as original.Length: 1.8125 inches. Width: 1.
Seal, fender skirt edge.Length: 60.0 inches. Width: .625 inches.
Bumper, front spring, upper arm (on frame).
Pad, accelerator pedal. Brown rubber. For black see our #70-0208-40. Made to slip over old metal core after removing old rubber.
Bottoming pads, rear axle. Rubber block mounts by bracket to rear axle tube.
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Bumper, door side. Square type held by four (4) screws, metal core as original.
Pads, brake and clutch pedals. Brown rubber. For black see our #70-0176-22.Color:brown Length: 3.8125 inches.
Bushings, front stabilizer bar. Fully molded rubber. One and five eighths inch (1 5/8") length by one and seven sixteenths inch (1 7/16') width by three fourths inch (3/4") inside hole diameter by one and eleven sixteenths inch (1 11/16") height.
Pad, accelerator pedal. Black rubber. For brown see our #70-0208-89. Made to slip over old metal core after removing old rubber.Length: 8.25 inches.
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Bulb type seal, gravel shield-to-rear bumper, anti-squeak. Also used as a door weatherstrip for some makes and models. Twelve (12) foot strip.
Bumper, side window glass in vent frame at top, right and left, brass core.Length: 1.625 inches.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Grommet, firewall , dash wires.Height: .50 inches.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Pads, brake and clutch pedals. Black rubber. For brown see our #70-0176-89.
Gasket, fog light body to ring or bezel.
Gasket, fog light lens to reflector.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Headlight door to lens seal. Molded without wire. Single lip type for sealed beams.
Grommet, steering column at floor, fits chrome ring.
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Conduit, hydraulic line & power window wire. Front doors only. 2 pieces cut nine and one half (9-1/2) inches.Length: 9.50 inches. Height: 1.50 inches.
Weatherstrip, front door opening, front body hinge pillar, lower. Extruded sponge to original configuration. Two (2) required per car.Width: .875 inches.
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.