This rear window gasket mounts around the full perimeter of the back glass and has the divider bars molded directly into it. It has properly molded corners to precisely conform to the glass and has the slot to accommodate the outer edge's decorative molding.
This six (6) piece Front Door Vent Window Set contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This seven (7) piece Front Door Weatherstrip Set is the primary seal for the doors to the body. The set includes the door bottom weatherstrip with molded corners, hinge pillar bellows, front edge seals, and rear edge seals.
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This Front Door Vent Window Weatherstrips contain the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
This Windshield Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends.
Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
This Trunk Weatherstrip is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Insulator, engine support rear, right and left. For models with a manual transmission. Revulcanization service only.
Insulator, engine support rear, right and left. For models with a Hydro-matic transmission. Revulcanization service only.
Insulator, engine support front. One (1) per car. Revulcanization service only.Length: 5.625 inches.
Revulcanization Service Only for Black Rubber Accelerator Pedal Pad. For Brown see our #27-0082-89.
This Front Suspension Bumper, front suspension lower A-arm, is made from high-quality EPDM rubber for a precise, factory fit.
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Weatherstrip, roof rail at hinge pillar.Width: 2.25 inches.
Revulcanization Service Only for Brown Rubber Accelerator Pedal Pad. For Black see our #27-0082-40.
Weatherstrip body hinge pillar
Weatherstrip, front door opening. Right and left, hinge pillar at beltline. Constructed of soft rubber.Length: 12.0 inches.
Bottoming pads, rear axle. Rubber block mounts by bracket to rear axle tube.
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Bumper, door side. Square type held by four (4) screws, metal core as original.
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Bumper, side window glass in vent frame at top, right and left, brass core.Length: 1.625 inches.
Bushings, for stabilizer bracket. Fully molded rubber. Correct dimensions, not an aftermarket replacement. One and three fourths inch (1 3/4') length by one and three eighths inch (1 3/8") width by three fourths inch (3/4") inside hole diameter by one and
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
This Hood to Cowl Weatherstrip mounts around the rear of the engine bay to seal between the hood and vehicle body cowl. The pair is twenty-one (21) inches in length and nine-sixteenths (9/16) inch in width to provide complete coverage.
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Headlight body mounting gasket. Rubber.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Weatherstrip, sash channel. Correct extrusion. Two (2) strips cut twenty five and one half (25-1/2) inches long.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Weatherstrip, auxiliary on body lock pillar. Correct extrusion cut thirty (30) inches long.
Boot, brake master cylinder rod. Fits on one and one fourth (1-1/4) inch diameter cylinder. Height: 2.125 inches.
Gasket, parking light housing.Length: 6.25 inches.
Gasket, back-up light housing.
This Side Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Pad, antenna mounting for manually operated antennas.
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Gasket, parking light lens and backup light lens. Die cut from one eighth (1/8) inch rubber.
Grommet, dimmer switch for carpet application.
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.