This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
This kit includes the weatherstrip components needed for the glass on your restoration project.
This ten (10)piece Convertible Roof Rail Weatherstrip Set fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
Door edge weatherstrip with molded ends. This part is the primary door to body weatherstrip. Includes pins and fasteners for easy installation.
This four (4) piece Front Door Vent Window Weatherstrip set is designed from the original parts for superior fitment and seal. This set contains the main vent window seals and division post seals.
This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This ten (10) piece set includes vent window division bars inner / outer window felt beltline weatherstrips for each side window and quarter window and a felt piece for above the rear quarters.
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends. It also has the slot to accommodate the top edge's decorative molding.
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This Automatic Transmission Mount pair supports the transmission and dampens vibration. Engineered and designed to OE standards. Steel core as original.
Seal, rear wheelhouse panel-to-quarter panel, outer. Two (2) five (5) foot strips, one for each side.Length: 60.0 inches. Width: .21875 inches.
This Clipped Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter and directly to the trunk lid using properly spaced plastic clips.
This six (6) piece Door Auxiliary Weatherstrip set is designed from the original part for superior fitment and seal. The Auxiliary Weatherstrip, also known as a "J" seal, installs on the door front at the beltline, right and left sides of the vehicle.
Weatherstrip, front door, auxiliary on body above beltline, hinge pillar windshield post. Two (2) strips, each thirteen and three eighths (13-3/8) inches long with retaining clips.
Brake and Clutch Pedal Pads - The proper design and fully detailed with ribs extending down over sides of the pad. Length: 3.50 inches. Width: 2.0 inches.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Bumper, folding top, side roof rail slat iron. Brass core as original. Two (2) or four (4) per car as required for front and center.Width: 1.5 inches.
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). This part is compatible to several Chevrolet model vehicles. Self-retaining, top quality. Height: 1.75 inches.
Accelerator Pedal Pad - Slip-over type made from top quality rubber. Length: 8.875 inches.
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Inner Fender Seal for anti-rattle, running board apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft lengths.
Front Stabilizer Bushing - Front stabilizer bar mounting. Fully molded rubber. Two (2) required per car. One and five sixteenths inch (1 5/16") length by one and five sixteenths inch (1 5/16") width by five eighths inch (5/8") inside hole diameter by one and three fourths inch (1 3/4") height.
Headlight body mounting gasket. Rubber.
Steele Rubber Products has the best quality Fenderskirt edge seal for your Street Rod or Custom Build project. Made from top-quality rubber to ensure durability and proper seal.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. This seal is the exact profile as original.
Bowdrill cloth tape is used for covering convertible side window weatherstrip. Available in a 5 ft roll.
This ten (10) piece Body Bumper Kit is designed from the original part for superior fitment, finish and function. Designed from originals and made from top quality rubber to ensure durability.
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Bumper, front suspension, lower arm. Steel core as original, excellent quality.
This Side Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
This convertible top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible top between the folding soft top and the top of the outer windshield.
Weatherstrip, folding top front bow-to-windshield, rear center section. Top quality sponge as original.
This black rubber Battery Clamp Cover helps to protect the nearby metal and finish. Good copy from an original part. Length: 3-1/2" inches.
This Hood to Cowl Weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. The strip is designed from the original part for superior fitment and complete coverage.
Seals, under taillight assembly. Die cut masticated rubber to authentic original dimensions.
Bowdrill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Grommet, cowl gutter drain hose. Nine sixteenth (9/16) inch hole through cowl side wall, five sixteenths (5/16) inch inside diameter. Two (2) per car.
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
This part is used as a front window regulator or accelerator rod through toe board seal. A front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
Bowdrill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
This Exhaust Tailpipe Hanger Strap is made from high-quality rubber for a precise, factory like fit for your classic vehicle. Muffler/tailpipe system, reproduction strap type is manufactured to OEM specifications.
This Hood to Fender Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle, order as needed.
This two (2) piece Splash Apron / A-Arm Dust Shield Set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Bushing, gearshift shaft lever, larger type. Three eighths (3/8) inch inside diameter by nine sixteenths (9/16) inch outside diameter barrel.Height: .
This Masticated Rubber Sheet is three thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Grommet, electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fits seven eighths (7/8) inch hole in light body. Two (2) to eight (8) per car as required.