Horn button contact cushion
p/n: 50-0409-21
Separator, horn contact. For standard or non-flexible wheel.
License Light Mounting Pad
p/n: 40-0391-85
Pad, trunk handle and license light housing.Length: 5.875 inches.
Flexible Run Channel - 5ft.
p/n: 70-1107-57
A cloth covered and mohair-lined type Flexible Run Channel. For sides and top of side windows. Available in 5- foot lengths.
Door Weatherstrip
p/n: 60-0114-73
Weatherstrip, door bottom, sponge constant section, solid skin surface, superior quality. Sold in six (6) foot strips only.Length: 72.0 inches.
Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Headlight Mounting Pad
p/n: 30-0142-14
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Windshield Gasket for V-Butted Glass - No Center Bar
p/n: 70-4812-52
This Windshield Gasket extrusion mounts around the full perimeter of the front glass. Used when removing center division bar and installing one (1) piece "V" Butted Glass. An extrusion only - NOT Spliced.
Floor Board Seals
p/n: 20-1595-88
This Floor Board Seal set contains all of the correct sealing components for the front floor boards.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Window Felt Beltline Weatherstrips - 3ft Pair
p/n: 30-0244-57
This side window Window Felt Beltline Weatherstrip pair can be used as inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Vent division bar weatherstrip
p/n: 50-0464-74
Weatherstrip, division post. Rear door on models with rear door vent. Made with metal core and attaching tabs like original.
Convertible Top Front Bow Weatherstrip
p/n: 70-0100-64
This Convertible Top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the top of the windshield.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Trunk Hinge Mounting Pad
p/n: 70-1229-87
Mounting pad, trunk hinge. Four (4) piece set.Length: 7.625 inches.
License Light Mounting Pad
p/n: 30-0122-17
Pad, rear license light mounting, with correct dimensions and beading.Length: 8.125 inches.
Door weatherstrip
p/n: 20-1649-73
Weatherstrip, back of door, vertical section. Material enough for all four doors, cut to fit at installation.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0054-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Cab Bumper
p/n: 60-0510-48
Bumper, cab hold down bolts. Comes as a pair of two (2). Fully molded rubber.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
Brake and Clutch Shank Seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Gearshift Boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Windshield Division Bar Gasket
p/n: 70-0372-51
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part is properly sized with "H" section. Part requires fitting to top and bottom, as it is not drilled.
Folding seat bumper
p/n: 70-0482-88
Rest pads, seat back, outer, on two (2) door styles with folding seats. Black rubber. For brown see our #70-0482-89. Self retaining, perfect copy.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Vent Division Bar Weatherstrip
p/n: 70-0772-56
This Front Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs.
Vent division bar weatherstrip
p/n: 70-0697-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent Division Bar Weatherstrip
p/n: 70-0695-74
Division bar seal. Proper cross section rubber molded to original style metal with authentic attaching tabs.
Vent division bar weatherstrip
p/n: 50-0317-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Trunk Handle / License Light Mounting Pad
p/n: 27-0035-17
This Trunk Handle and License Light Mounting Pad is designed from the original part for an authentic fit, finish, and appearance.
Vent division bar weatherstrip
p/n: 70-0694-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Clutch or Brake Pedal Pad - Black
p/n: 70-0176-22
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Vent Window Division Post Weatherstrips
p/n: 60-0494-56
This front door Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. Fully molded rubber with metal core and attaching tabs.
Vent Window Division Post Weatherstrips
p/n: 60-0569-56
This Front Window Vent Division Post Weatherstrip pair is fully molded with metal core and attaching tabs.
Fuel Neck Grommet
p/n: 40-0352-39
Grommet, fuel filler neck, exact copy with thirty (30) degree slope. Fully molded rubber with retaining flange. Three and five sixteenths inch (3-5/16") outside width by four and one eight inch (4-1/8") outside length.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Vent Division Bar Weatherstrip
p/n: 70-2089-56
This Front Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs.
Fuel Neck Grommet
p/n: 60-0401-41
Grommet, fuel filler neck. Fully molded, slightly angled. Four and one fourth inch (4-1/4") inch outside diameter by two and one eighth inch (2-1/8") inside hole diameter by seven eights inch (7/8") height at front.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Clutch Control Boot
p/n: 30-0273-24
Boot, clutch control unit governor.1940-42: Cars with Overdrive 1941-42: Cars with Electromatic
Hood Bumper
p/n: 70-0409-42
Bumpers, hood top panel at cowl. One half (1/2) inch by one half (1/2) inch by three and one fourth (3-1/4) inch. Held in place by screws. Two (2) to four (4) per car as required.
Beltline Weatherstrips
p/n: 40-0539-57
This Beltline Weatherstrip pair installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
Vent division bar weatherstrip
p/n: 30-0346-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Brake and Clutch Shank Seal
p/n: 40-0217-24
Draft cap for brake and clutch pedal.Length: 2.4375 inches. Width: 1.6875 inches.
Vent division bar weatherstrip
p/n: 30-0347-74
Weatherstrip, rear vent window, front edge (on division post) right and left.
Engine Snubber Pad Set
p/n: 30-0311-11
This four (4) piece Engine Snubber Pad Set is designed from original for correct fit and function. Sold only in complete sets. One four (4) piece set required per car.
Flexible Run Channel - 6 Ft.
p/n: 70-1108-57
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
Cowl Vent Gasket
p/n: 30-0262-54
Gasket, cowl vent. Labyrinth style as original.Length: 12.75 inches.
Steering Column Grommet - Black
p/n: 60-0621-36
This black rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.
License Light Mounting Pad
p/n: 60-0099-17
This Rear License Light Mounting Pad is designed from the original part for an authentic fit, finish, and appearance. Length: 9 inches.
Taillight Lens Gasket
p/n: 70-1213-15
Gasket, taillight lens. For the main pad order our #70-1212-15.Length: 6.875 inches.
Rear Valance Gasket Strip
p/n: 70-0461-45
This Rear Valance Gasket Strip installs on the gravel shield to body. Designed from the original part so it fits correctly. Customer will need to cut bolt clearance as needed.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Steering Column Grommet - Brown
p/n: 60-0621-89
This brown rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.
Brown seat back rest pad
p/n: 70-0482-89
Rest pads, seat back, outer, on two (2) door styles with folding seats. Brown rubber. For black see our #70-0482-88. Self retaining, perfect copy.
Front Bow Weatherstrip
p/n: 60-0440-64
Weatherstrip, front bow to windshield, outer. Installs on convertible top. Approximately four (4) foot ten (10) inches long.
Accelerator Pedal Service
p/n: 60-0701-40
Pedal, accelerator. Revulcanization service only. Excellent cover detailing with molded in rod ball socket as original.
Rear Engine Mount
p/n: 20-0421-11
This Rear Engine Mount helps eliminate engine vibrations. Used as a rear engine support or transmission mount. Designed with rubber over a metal core.
Gearshift Boot - Black
p/n: 20-0334-26
This reproduction Black Gearshift Boot is designed from the original part for an authentic fit, finish, and appearance.
Hood Corner Pad
p/n: 60-0118-42
Pad. hood corner, steel core as original, front and rear.Length: 1.5 inches.
Exterior Windshield Division Bar
p/n: 20-2341-51
This stainless steel Exterior Windshield Division Bar is designed from the original part for superior fitment, appearance and function.
Rear Window Gasket
p/n: 20-1668-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket
p/n: 20-0395-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 20-1660-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Cowl Vent Gasket
p/n: 40-0271-54
Gasket, cowl vent. Fully molded to original cross-section and outline.Length: 18.0 inches.
Fuel Neck Grommet
p/n: 40-0043-39
Grommet, fuel filler neck. Fully molded rubber with retaining flange. Three and five eighths inch (3-5/8") outside diameter by two and one eighth inch (2-1/8") inside diameter by one inch (1") height.
Door Hinge Weatherstrips
p/n: 20-1643-73
This Door Hinge Weatherstrip pair is designed from the original parts for superior fitment and sealing. These door edge weatherstrips are molded specifically to fit the door hinge area of the vehicle.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Rear Gravel Deflector to Bumper Seal
p/n: 60-0020-30
This Rear Gravel Deflector to Bumper Seal is made of a high quality EPDM dense rubber extrusion. Designed from the original part so it fits correctly. Sold as a six (6) foot strip.
Flexible Run Channel
p/n: 20-1146-58
This Flexible Run Channel helps to eliminate window rattle, provides a smooth sliding surface for glass movement, and works to protect the glass. Stainless steel beaded. Available in sixty (60) inch strips.
Front Stabilizer Bushing
p/n: 30-0123-33
Bushings, front stabilizer mounting bracket. Fully molded rubber.
Window Pinchweld Seal
p/n: 70-0096-52
This twelve (12) foot Window Pinchweld Seal is designed from the original part for superior fitment and function. The part is used to seal and retain an outer decorative reveal molding. Used with our 70-1192-52.
Front Fender Seals
p/n: 60-0522-45
Seal, front fender baffle, right and left. One (1) pair per car. Length: 5-1/4" inches.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Flexible Run Channel - 60 Inch
p/n: 20-1619-58
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
Overload Spring Arm Bumpers
p/n: 70-2301-32
A reproduction Overload Spring Arm Bumper pair manufactured to OEM specifications. Fully molded quality rubber bumpers that installs in the truck's overload spring arms.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Clutch Equalizer Bushing and Seals
p/n: 70-2029-24
This Clutch Equalizer Bushing and Seal set is designed from the original part for superior fitment and operation. The set includes a metal sleeved rubber bushing and two (2) molded rubber seals for each end of equalizer shaft.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Suspension bushing
p/n: 30-0341-36
Bushing, insulator, upper support arm, outer above steering knuckle support. Four (4) piece set.
Door Bumper
p/n: 34-0305-71
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
License Light Mounting Pad
p/n: 70-0559-17
Pad, license light bracket or base mounting. Two (2) per car.
Accelerator Pedal Pad
p/n: 70-0208-40
Pad, accelerator pedal. Black rubber. For brown see our #70-0208-89. Made to slip over old metal core after removing old rubber. Length: 8.25 inches.
Clutch and Brake Pedal Pads - BLACK
p/n: 25-0024-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Black rubber.