Glass Weatherstrip Kit
p/n: 90-3078-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Body Weatherstrip Kit
p/n: 90-3102-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Body Weatherstrip Kit
p/n: 90-3101-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Window Felt and Run Channel Set
p/n: 90-0141-58
This ten (10) piece Window Felt and Run Channel set includes the inner and outer window felts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Rear Window Gasket
p/n: 50-0215-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Front Door Vent Window Set
p/n: 90-0418-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Steering Column Floorplate
p/n: 70-2578-36
Floor plate, steering column at floorboard. Durable black rubber construction with metal core just like original.
Windshield Gasket
p/n: 50-0212-50
This Windshield Gasket is has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the reveal molding across the top only.
Rear Quarter Stationary Window Weatherstrips
p/n: 70-2573-77
This Rear Quarter Window Weatherstrips pair is designed from the original part for superior fitment and seal. This one-piece weatherstrip mounts around the full perimeter of the quarter glass for a precise, factory fit. For stationary (fixed) windows only.
Axle Rebound Pad
p/n: 50-0371-35
Bumper, rear axle. Revulcanization service only.Height: 3.5 inches.
Front Door Vent Window Weatherstrips
p/n: 38-0081-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Engine Mount Service – Revulcanization Only
p/n: 50-0274-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Door Weatherstrips
p/n: 50-0533-72
This Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Push-on pin type door weatherstrips mount directly to the doors to seal against the full door perimeter to the vehicle body.
Front Door Weatherstrip
p/n: 70-2259-72
This Front Door Weatherstrip pair is designed from the original parts for superior fitment and seal. These primary front door weatherstrips are like the 1st type to be glued in to seal the driver and passenger doors when closed.
Rear Door Weatherstrip
p/n: 50-0534-72
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Taillight Mounting Pad
p/n: 50-0382-15
Taillight to fender mounting pad. Excellent quality molded piece with all correct details. Four (4) required per car.
Transmission Mount Service
p/n: 50-0264-25
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Transmission Mount Service
p/n: 50-0263-25
Support, transmission (insulator). Revulcanization service only. See also our #50-0262-25, many models use both.Length: 5.0 inches. Width: 1.875 inches.
Transmission Mount Service
p/n: 50-0262-25
Pad, transmission mounting, thrust. Revulcanization service only. One (1) per car required. See also our #50-0263-25. Many models use both.Length: 7.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Trunk Weatherstrip
p/n: 50-0483-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Axle Rebound Pad
p/n: 50-0370-35
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
Trunk Emblem Mounting Pad
p/n: 50-0185-17
Mounting pad, trunk emblem base, made in three pieces. Customer will have to modify outer holes.Width: 23.0 inches.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Hood to Cowl Weatherstrip
p/n: 50-0561-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. Part is pre-drilled with 12 holes and includes button retainers.
Door Auxiliary Weatherstrips
p/n: 60-0342-73
This six (6) piece Door Auxiliary Weatherstrip set is designed from the original part for superior fitment and seal. The Auxiliary Weatherstrip, also known as a "J" seal, installs on the door front at the beltline, right and left sides of the vehicle.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Vent division bar weatherstrip
p/n: 60-0534-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Front Coil Spring Pad
p/n: 50-0476-35
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0054-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Parking and Signal Gasket
p/n: 50-0354-16
Gasket, front parking and signal light to fender. One (1) pair per car. Fits between signal lamp body and headlamp to fender adapter.Width: 4.0 inches.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Parking Light Lens Gasket
p/n: 50-0351-16
Gasket, headlight door parking lens. Constructed out of soft durable rubber.Height: .375 inches.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Brake Pedal Pad
p/n: 50-0349-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. For models with Power Brakes.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Parking Light Lens Gasket
p/n: 50-0353-16
Gasket, front parking lens. High quality sponge rubber better than original. One (1) pair per car.Width: 3.375 inches. Height: 2.625 inches.
Parking Brake Pedal Pad
p/n: 50-0348-22
Pad, parking brake pedal. Without "PARK" written on pad. Black only. For pedal pad with "PARK" written on pad see our #50-0405-22.Height: 2.0 inches.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Door Handle Gasket Set
p/n: 70-2673-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Reflector gasket
p/n: 50-0360-15
Seal, reflector signal, between taillights. With correct slits for tabs on reflector. One (1) pair required per car.
Brake Pedal Pad - Dyna-Flow Transmission
p/n: 50-0285-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. For models with Dyna-Flow and standard brakes.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Firewall Grommet
p/n: 70-2067-20
This Firewall Grommet is used to run the main wiring harness through the firewall. Designed from the original part for superior fit and seal.
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
Firewall Grommet
p/n: 70-2066-24
This Firewall Grommet is used to run the emergency brake cable through the firewall. Designed from the original part for superior fit and seal.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
1-5/8" Firewall Grommet
p/n: 70-2063-20
This Firewall Grommet is used to run the speedometer cable line through the firewall. Designed from original part for excellent workmanship.
1-5/8" Firewall Grommet
p/n: 70-2062-20
This Firewall Grommet is used to run the oil pressure and temperature line through the firewall. Designed from original parts for excellent workmanship
1-5/8" Firewall Grommet
p/n: 70-2064-20
This Firewall Grommet is used to run the vacuum hose and ignition resistor wire through the firewall. Designed from the original part for excellent workmanship.
Body Mounting Pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
1-3/16" Standard Grommet
p/n: 32-0328-54
This Standard Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
1-3/8" Parking Brake Grommet
p/n: 50-0555-20
This Parking Brake Grommet is used to run the parking brake cable through the frame. Designed from original part for excellent workmanship.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Body Mounting Pad
p/n: 50-0097-48
Pad, several usages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car.
Axle Rebound Pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car.
Hood Bumper
p/n: 50-0490-42
Bumper, hood to fender. Uses four (4) per car for most models.Width: 1.375 inches. Height: 1.25 inches.
1-5/8" Cowl Hole Grommet
p/n: 70-2065-20
This Firewall Grommet is used to plug the hole on the cowl side of the firewall. Designed from original part for excellent workmanship.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as a window stop cushion for front and rear door, rear side and quarter windows as required.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
3/4" Trunk Weatherstrip
p/n: 70-0463-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
11/16" Door Weatherstrip
p/n: 70-0491-73
This Door Weatherstrip for the side window is made of an extruded sponge rubber. The weatherstrip is the larger type that is used on most GM cars this period. Available by the foot.
9/16" Trunk Weatherstrip
p/n: 60-0411-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Vacuum Pump Mounting Cushion
p/n: 70-1571-24
Mounting cushion, vacuum pump. Three (3) per car required.Width: .625 inches.
Lock Cylinder Gasket
p/n: 70-0955-86
Gasket, trunk lock cylinder. Steel rule die cut from one thirty seconds (1/32) inch dense rubber.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
5/8" Door Weatherstrip
p/n: 70-0219-73
The Door Weatherstrip is designed for 1941-1957 GM and Mopar vehicles but with its generic shape it has many uses outside of its original purpose. Available by the foot.
1-3/16" Utility Plug
p/n: 35-0099-20
This Utility Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
1" Floor Pan Grommet
p/n: 35-0515-20
This Floor Pan Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Firewall Retainer
p/n: 60-0586-20
This Firewall Retainer is used on the firewall insulation panel. Designed from original for the "Christmas Tree" style popular during this time.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Door Lock Bumper
p/n: 34-0484-71
This Door Lock Bumper is made from high-quality EPDM dense rubber to provide excellent durability. Designed for applications such as the upper door lock post.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.