Window Felt and Run Channel Set
p/n: 90-0141-58
This ten (10) piece Window Felt and Run Channel set includes the inner and outer window felts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Front Door Weatherstrip Set
p/n: 90-0111-72
This eight (8) piece Front Door Weatherstrip set is the primary weatherstripping for the doors to the vehicle body. The set includes the door bottom weatherstrip with molded corners, the hinge pillar bellows, the front edge seals, and the door edge weatherstrip.
Front Door Vent Window Set
p/n: 90-0401-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Windshield Gasket
p/n: 60-0151-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Engine Mount Service – Revulcanization Only
p/n: 25-0072-11
This Revulcanization Service Only is designed to restore your Right and Left Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Front Door Vent Window Weatherstrips
p/n: 38-0059-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Door Weatherstrip
p/n: 60-0250-73
Weatherstrip, door bottom and corners, molded right and left. Overall length forty and three fourths (40-3/4) inch per door.
Rear Window Gasket
p/n: 60-0152-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Trunk Weatherstrip
p/n: 70-0870-84
This Trunk Weatherstrip is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Rear axle bushing
p/n: 25-0081-32
Insulators, rear axle housing, upper and lower. Four (4) piece set.
Trunk Weatherstrip Set
p/n: 70-0871-84
This Trunk Weatherstrip Set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the decklid.
Engine Mount Service – Revulcanization Only
p/n: 25-0077-11
This Revulcanization Service Only is designed to restore your Front Lower Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 25-0062-11
This Revulcanization Service Only is designed to restore your Front Upper Engine Mount at Crossmember to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Trunk Weatherstrip Corners
p/n: 70-1038-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Fender Skirt Edge Weatherstrip
p/n: 25-0092-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Fender Skirt Edge Weatherstrip
p/n: 70-0289-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Front Spring Rubber Bumpers
p/n: 70-0329-32
This Front Spring Rubber Bumper Pair fits to the upper control arms on frame. Manufactured to OEM specifications to install for an authentic fit, finish and function.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Vent Window Division Post Weatherstrips
p/n: 60-0494-56
This front door Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. Fully molded rubber with metal core and attaching tabs.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Gearshift Boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Fender Skirt Edge Weatherstrip
p/n: 60-0109-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Window Stop Stem Bumpers
p/n: 33-0675-62
This Window Stop Stem Bumper pair is designed from the original part for an authentic fit, finish, and appearance. Cushion window stop pair for the lower front and or rear doors rear side and quarter windows as needed.
Parking/Backup Light Lens Gaskets
p/n: 70-1272-16
This Parking/Backup Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Housing or Bezel. Die-cut from one-eighth (1/8") inch sponge rubber.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Wiper Transmission Gasket
p/n: 27-0052-53
Gasket, windshield wiper transmission made of the highest quality and authenticity. Replaces #4562197.
Wiring Grommet
p/n: 70-0355-14
This Wiring Grommet is used to run electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fully molded from top-quality EPDM dense rubber to provide excellent durability.
Window Stop Stem Bumper
p/n: 33-0622-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
15/16" Trunk Weatherstrip
p/n: 70-0490-85
This Trunk Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
7/8" Door Weatherstrip
p/n: 70-0492-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Wiper control grommet
p/n: 60-0197-53
Grommet, wiper control connection link. Replaces #4161287. 11/32" I.D. X 19/32" O.D.
3/4" Trunk Weatherstrip
p/n: 70-0463-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
11/16" Door Weatherstrip
p/n: 70-0491-73
This Door Weatherstrip for the side window is made of an extruded sponge rubber. The weatherstrip is the larger type that is used on most GM cars this period. Available by the foot.
1-1/16" Firewall Grommet
p/n: 25-0098-20
This Firewall Grommet is used to run the oil pressure gauge line through the firewall. Designed from original part for excellent workmanship.
13/16" Trunk Weatherstrip
p/n: 50-0161-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
9/16" Trunk Weatherstrip
p/n: 60-0411-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Brown Door Lock Knob
p/n: 70-0354-70
This is the knob or button for the inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. The part fits many different vehicles.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Steering Knuckle Support Seal
p/n: 50-0199-35
This Steering Knuckle Support Seal is designed from the original part for an authentic fit, finish, and appearance. Fits at the steering knuckle support at the upper pivot pin. Four (4) required per car.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
9/16" Channel filler weatherstrip
p/n: 70-0489-58
Weatherstrip, channel filler, door window sash channel and some quarter window sash channel. Special type with wide weatherstrip edge to be trimmed at assembly, when necessary. Available by the foot.
5/8" Door Weatherstrip
p/n: 70-0219-73
The Door Weatherstrip is designed for 1941-1957 GM, Mopar and Packard vehicles but with its generic shape it has many uses outside of its original purpose. Available by the foot.