Engine Mount Service – Revulcanization Only
p/n: 50-0256-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Window Felt and Run Channel Set
p/n: 90-0140-58
This eight (8) piece Window Felt and Run Channel set includes the inner and outer window felts, upper rigid run channels, and flexible run channels needed to complete two doors. The set can be used for front or rear doors in models with vent windows in the door.
Window Felt and Run Channel Set
p/n: 90-0142-58
This six (6) piece Window Felt and Run Channel set includes the inner and outer window felts and the flexible run channels needed to complete two (2) doors. This set is used for front or rear doors in models without vent windows in the door.
Front Door Vent Window Set
p/n: 90-0365-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0015-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Engine Mount Service – Revulcanization Only
p/n: 50-0234-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Windshield Gasket
p/n: 70-0535-50
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Front coil spring pad
p/n: 50-0306-35
Insulator ring, front coil spring, top and bottom. Four (4) per car.
Door Weatherstrip
p/n: 70-0085-73
Weatherstrip, door opening, fits retainer under edge of body sill to form seal when door is closed. Six (6) foot strips.Length: 72.0 inches. Width: 1.
Trunk Weatherstrip
p/n: 70-0083-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Front Suspension Rebound Pad
p/n: 50-0083-32
Rebound pad, front suspension, upper arm, on frame. Rubber body, steel core with five sixteenths (5/16) inch stud.
Transmission Mounting Pad
p/n: 50-0335-25
Transmission support pad, insulator blocks, upper and lower.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Windshield Division Bar Gasket
p/n: 70-0247-51
Gasket set, windshield divider post, inner and outer. Two (2) piece set with screw holes and pilots.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0049-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Pads - Black
p/n: 50-0049-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Windshield Division Bar Gasket
p/n: 70-0159-51
This inner and outer Windshield Division Bar Gasket acts as a retainer for the outer division bar chrome molding.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Accelerator Pedal Pad
p/n: 50-0038-40
Pad, accelerator pedal. Rubber flanges all around as original to fit over pedal core. Length: 9.125 inches.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Front Coil Spring Pad
p/n: 50-0476-35
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Rumble Seat Step Mounting Pad
p/n: 50-0182-44
Mounting pad, rumble seat step to fender, proper beaded edge, exact copy.Width: 4.8125 inches.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Antenna Boot
p/n: 70-0212-21
This Antenna Boot is designed from the original part for superior fitment and function. This boot fits at the vehicle running board antenna wire connection.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
2-1/4" Firewall Grommet
p/n: 50-0166-20
This Firewall Grommet is used to run the wiring harness through the firewall mat. Designed from the original part for superior fit and seal.
Glovebox Door Check Grommet
p/n: 70-0285-88
Grommet, glovebox door check link, for one and one eighth (1-1/8) inches slot in dash.Length: 1.4375 inches. Width: .625 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Windshield Wiper Transmission Gaskets
p/n: 70-1196-53
This Windshield Wiper Transmission Gasket pair is designed from the original part for superior fitment and function. This gasket mounts between the windshield wiper transmission and the vehicle body work to reduce noise and vibration.
Radius or Panhard Rod Bushing
p/n: 50-0303-35
This rear axle Radius or Panhard Rod Bushing is a quality reproduction of the original factory part. A fully molded rubber bushing that works to cushion road vibration at the rod end. Four (4) required per car.
1-1/2" Firewall Grommet
p/n: 50-0299-20
This Firewall Grommet is used to run the oil pressure and water temperature lines through the firewall. Designed from original part for excellent workmanship.
Front Bumper Gravel Shield
p/n: 70-0127-30
This anti-rattle Front Bumper Gravel Shield pad is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over a corrosion resistant brass core to ensure durability, fit and appearance.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Front Engine Mounting Pad
p/n: 50-0229-11
This Engine Mount Pad is designed to original specifications with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Door Check Link Rod End Stop Washer
p/n: 70-0384-70
A quality Door Check Link Rod End Stop Washer for door check mechanism. One and seven-sixteenths (1-7/16") inch diameter by three-sixteenths (3/16") inch thick.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Brown Door Lock Knob
p/n: 70-0354-70
This is the knob or button for the inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. The part fits many different vehicles.
Door Check Link Rod End Stop
p/n: 70-0325-70
A quality Door Check Link Rod End Stop for rod type door check mechanism. One (1") inch diameter by three-eighths (3/8") inch thick with five-sixteenths (5/16") inch hole.
11/16" Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel. Available by the foot.
9/16" Door Edge Weatherstrip
p/n: 70-0411-73
This Door Edge Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Brake Cable Shielding Cover - 2 Inch
p/n: 70-1701-24
This two (2) inch long Brake Cable Shielding Cover is designed install for an authentic fit, finish and function. Fits all models with seven sixteenths (7/16) inch outside diameter cable.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
11/16" Channel Filler Weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel. Available by the foot.
7/8" Window Weatherstrip
p/n: 70-1191-52
This Window Weatherstrip is for models without chrome reveal molding. Available by the foot.
7/8" Window Weatherstrip
p/n: 70-1192-52
This Window Weatherstrip is for models with chrome reveal molding. Available by the foot.
7/8" Windshield Weatherstrip
p/n: 70-1190-52
This Windshield Weatherstrip is for windows without chrome reveal molding. For a 2-piece windshield, select gasket for division bar. Available by the foot.
Side Window Bumper
p/n: 60-0195-62
Anti-rattle, side window, inner and outer. Fits slot in outer door body metal and inner window frame (garnish molding).
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
1" Wiring Grommet
p/n: 32-0047-14
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed to run the electric wire through the body for head and taillights.
5/32" Side Mount Tire Cover Seal
p/n: 50-0541-37
High-quality dense rubber seal, for a variety of uses. Available by the foot.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
1/2" Standard Bumper
p/n: 33-0136-42
This Standard Bumper is fully molded from quality dense rubber to provide excellent durability. Commonly used as a door bumper on the center upper post on post model vehicles.
Door Weatherstrip Fastener Clip
p/n: 70-0303-73
Metal Fastener clips, sold as an each, for attaching door edge weatherstrips. For one fourth (1/4) inch holes. Doors usually require one (1) clip per every six (6) inches.
5/16" Standard Stem Bumper - GM
p/n: 33-0127-41
This 5/16" Standard Stem Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a console and fuel filler door bumper on GM models.
5/16" Glovebox Door Bumper
p/n: 33-0128-88
This 5/16" Glovebox Door Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a glovebox door bumper on GM models.
Door Weatherstrip Fastener Retaining Clip
p/n: 70-0391-73
This Door Weatherstrip Retaining Clip is manufactured to OEM specifications to install for an authentic fit, finish and function. A direct-fit for Lower Door Weatherstrip 70-0066-73. Fits one-fourth (1/4") inch holes. Usually requires one clip per every six (6") inches.