Search Results
Please click on the part name in red in order to get a complete description.
Side window run channel kit
p/n: 90-0140-58
This eight (8) piece kit includes the inner and outer windowfelts, upper rigid run channels, and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models with vent windows in the door. Models with wood in the doors use our #70-1168-58 as lower rigid run channel.
Front Door Weatherstrip Kit
p/n: 90-0100-72
Front door weatherstrip. This set is the primary seal for the door to the body. Set includes the door perimeter weatherstrip and the door bottom weatherstrip. Enough for two (2) doors. Includes fasteners.
Front Door Vent Window Kit
p/n: 90-0373-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Motor mount service
p/n: 25-0064-11
Motor mount, rear. Revulcanization service only.Length: 4.0 inches.
Front Door Vent Window Weatherstrips
p/n: 38-0029-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Windshield Gasket
p/n: 50-0250-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 50-0206-81
This rear window gasket set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Quarter window weatherstrip
p/n: 27-0040-77
Weatherstrip, fixed rear quarter window. Vulcanized in one piece for easy application, no splicing required.
Brown accelerator service
p/n: 25-0094-89
Accelerator pedal. Brown rubber. For black see our #25-0094-40. Revulcanization service only. Includes new rubber sockets at base and for pedal rod.
Motor mount service
p/n: 25-0062-11
Motor mount, upper front at cross member. One (1) per car. Revulcanization service only.Length: 4.75 inches. Width: 2.25 inches.
Trunk Weatherstrip
p/n: 70-1128-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Accelerator pedal service
p/n: 25-0094-40
Accelerator pedal. Black rubber. For brown see our #25-0094-89. Revulcanization service only. Includes new rubber sockets at base and for pedal rod.
Trunk Weatherstrip
p/n: 70-1129-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Rear bumper grommet
p/n: 70-0164-29
Grommets, rear bumper. (Some cars have this type, some have our #70-0144-29, sold separately. They are both interchangeable and original). Fully molded rubber. Four inches (4") outside length by two and one eighths inch (2-1/8") outside width by one and f
Detachable center post pad
p/n: 70-0280-88
Pads, folding front seat rest, brass core. Also used as bumper, slat iron to compartment on convertibles.Width: 1.375 inches. Height: .28125 inches.
Rumbleseat Weatherstrip
p/n: 70-0282-85
These rumbleseat weatherstrips are designed from the original part for superior fitment and seal. The pieces are molded as left and right for the lower corners.
Windshield division bar gasket
p/n: 70-0159-51
Gasket, windshield division post, inner and outer, also acts as retainer for outer division bar chrome, molding.
Torque ball boot
p/n: 25-0034-24
Cushion, propeller shaft (drive shaft) bearing.Height: 1.0625 inches.
Front suspension bumper
p/n: 50-0125-32
Bumper, front suspension, lower arm.Width: 2.625 inches. Height: 2.5625 inches.
Front bumper grommet
p/n: 25-0010-28
Grommet, front bumper, right and left. Hollow back, original copy.Length: 4.0625 inches.
Brown brake and clutch pad
p/n: 25-0024-89
Pads, brake and clutch pedal, authentic type ribbing, proper size, top quality rubber. Brown rubber. For black see our #25-0024-22.
Front Stablizer Bar End Link Kit
p/n: 70-0567-34
Kit, stabilizer bar link assembly. Twenty two (22) piece set for both sides of one (1) car, front and rear. (Order 2 sets if you need both). Hex head bolt. 5/16"-24nf x 7-5/8" lg. Comes with metal sleeve, cup washers and rubber grommets.
Fuel neck grommet
p/n: 25-0013-41
Grommet, fuel filler neck. Virtually exact copy for two and one fourth (2-1/4) inch diameter filler neck through body or fender.
Trunk bumper
p/n: 50-0163-87
Bumper, trunk. Brass core, screw held. Two (2) per car.Length: 1.5 inches. Width: .75 inches.
Front Spring Rubber Bumper
p/n: 70-0329-32
Front Spring Rubber Bumper - for upper control arm on frame.
Brake and clutch pedal pad
p/n: 25-0024-22
Pads, brake and clutch pedal, authentic type ribbing, proper size, top quality rubber. Black rubber. For brown see our #25-0024-89.Length: 3.125 inches.
Brake and clutch shank seal
p/n: 25-0051-24
Seals, brake and clutch pedal shank-to-toe board, sponge rubber. Two (2) per car.
Rigid Run Channel
p/n: 70-0347-58
Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.
Flexible Run Channel 6 Foot
p/n: 70-1239-58
Window run channel with stainless beaded edge. Six (6) foot length. Cloth covered, mohair lined, flexible channel for sides and top of door windows. Exact replacement for listed vehicles but can be used in many applications.
Beltline weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Brown gearshift boot
p/n: 50-0035-89
Boot, gearshift. Brown rubber. For black see our #50-0035-24.Color:brown Width: 2.8125 inches.
Vent division bar weatherstrip
p/n: 70-0791-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Flexible Run Channel 5 Foot
p/n: 70-1238-58
Window run channel, stainless beaded edge. Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Perfect dimensions, Five eighths (5/8) inch wide by nine sixteenths (9/16) inch overall height, exact replacement. Five (5) fo
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender welting 3/16 bead 25ft
p/n: 70-1099-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Steel sash channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Gearshift boot
p/n: 50-0035-24
Boot, gearshift. Black rubber. For brown see our #50-0035-89.Width: 2.8125 inches.
Starter pedal pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Battery carrier edge liner
p/n: 27-0091-21
Seal strip, battery to fender apron. Two (2) correct cross section strips nineteen (19) inches long.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Wiper transmission gasket
p/n: 70-1197-53
Gasket, windshield wiper transmission. Replaces #4074294 & #4082366.
Door check link rod end stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Side window run channel
p/n: 70-1168-58
Channel, side window, pre-flocked, five sixteenths (5/16) inch wide base for one fourth (1/4) inch glass. Most Fisher closed bodies except those using stainless beaded channel. For nine sixteenths (9/16) inch wide channel, see our #70-1169-58.
Side window run channel
p/n: 70-1169-58
Channel, side window, pre-flocked, nine sixteenths (9/16) inch wide to accommodate metal frame side window.
Fabric hood lacing
p/n: 60-0578-42
Lacing, hood, fabric, webbing anti-squeak. With hollow center to receive wire if needed, or fasten with rivets if so found originally. Excellent quality. Seven eighths (7/8) inch by one eighths (1/8) inch thick.
Fabric hood lacing
p/n: 70-2221-42
Lacing, hood, fabric, webbing anti-squeak. DOES NOT have hollow center. Fasten with rivets if so found originally. Excellent quality.
Door bumper
p/n: 34-0025-42
Bumper, front and rear body hinge pillar, one (1) inch diameter by one fourth (1/4) inch thick, held by screw, steel core. Auxiliary, used only where needed to prevent door rattle.Note: also used on 1942-50 Packards with Clipper styling near t
Door bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Brown door lock knob
p/n: 70-0660-70
Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Steering knuckle support seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Brown door lock knob
p/n: 70-0354-70
Knob for inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. See also our #70-0660-70.
Shock and stabilizer grommet
p/n: 70-0274-33
Grommet, shock and stabilizer link. Eight (8) required per car. Fully molded rubber with locating collar. One and one sixteenth inch (1 1/16") outside diameter by nine sixteenths inch (9/16") locating collar outside diameter by three eighths inch (3/8") i
Door check link rod end stop
p/n: 70-0325-70
Pad, door check link. For rod type door check. One (1) inch diameter by three eighths (3/8) inch thick with five sixteenths (5/16) inch hole.
Brake cable anti-rub cover
p/n: 70-1701-24
Anti-rub cover, brake cable. Fits all models with seven sixteenths (7/16) inch outside diameter cable.Width: 2.0 inches.
Door Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 70-0411-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Pressure ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel.Width: .375 inches. Height: .6875 inches.
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Body hole plug
p/n: 35-0863-45
Plug, body sheet metal holes. Used in various places (like trunks). For one and one half (1-1/2) inch hole in body.
Door weatherstrip
p/n: 70-0066-73
Seal, door bottom, held by metal track or by clips. (See our # 70-0391-73 for clips). 2 door styles need about seven (7) foot per car.
Side window bumper
p/n: 60-0195-62
Anti-rattle, side window, inner and outer. Fits slot in outer door body metal and inner window frame (garnish molding).Width: .75 inches. Height: .
Windshield Weatherstrip
p/n: 70-1190-52
Channel, windshield, for windows without chrome reveal molding. (With 2 piece windshield, select gasket for division bar).
Channel filler weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel.Width: .375 inches. Height: .
Sash channel filler 1/16 cork
p/n: 70-1115-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Sash Channel Filler 1/16 Rubber
p/n: 70-2170-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Sash channel filler 1/32 cork
p/n: 70-1114-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition
Sash Channel Filler 1/32 Rubber
p/n: 70-2169-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.
Side window weatherstrip
p/n: 70-0079-58
Weatherstrip, side window lower edge, retained in metal flap on side of carrier channel, seals out water when window is cranked up.Width: .375 inches.
Hood bumper
p/n: 70-0294-42
Bumper, hood rest, cap type for adjustable screw, fifteenth sixteenths (15/16) inch, seven sixteenths (7/16) inch thick.
Hood bumper
p/n: 33-0031-42
Bumper, hood, self-retaining, along edge of hood against fender. One half (1/2) inch outside diameter, for five sixteenths (5/16) inch hole in sheet metal.
Door weatherstrip fastener
p/n: 70-0303-73
Metal clip for attaching door edge weatherstrip, our #70-0411-73. For one fourth (1/4) inch holes. Doors usually require one (1) clip per every six (6) inches. Estimate needs accordingly.
Shock Absorber Arm Bushing
p/n: 60-0216-33
Bushing, for double acting shock absorber arm link. Height: .78125 inches.
Trunk or hood bumper
p/n: 34-0203-42
Bumper, trunk or hood. Molded with clearance for screw. Used for: Buick 1942-50 Bumper for trunk. Chevrolet 1949-55 Bumper for rear hood corners on cowl. Chevrolet 1949-50 Bumper for trunk. Oldsmobile 1938 Bumper under hood corner on radi
Door weatherstrip fastener
p/n: 70-0391-73
Clip, door bottom weatherstrip retaining, for our #70-0066-73 lower door weatherstrip, to fit one fourth (1/4) inch holes. Doors usually require one clip per every six (6) inches. Estimate needs accordingly.
