Search Results
Please click on the part name in red in order to get a complete description.
Side window run channel kit
p/n: 90-0140-58
This eight (8) piece kit includes the inner and outer windowfelts, upper rigid run channels, and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models with vent windows in the door. Models with wood in the doors use our #70-1168-58 as lower rigid run channel.
Front Door Vent Window Kit
p/n: 90-0373-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Motor mount service
p/n: 25-0065-11
Motor mount, rear. Revulcanization service only.1939-48: All 6 cylinder 1939-48: All 8 cylinder with hydramatic transmission (exc. 1948 Ser.
Front Door weatherstrip
p/n: 90-0104-72
Door edge weatherstrip. This part is the primary door to body weatherstrip. Includes 22 ft (11ft per dr) of main door seal, 7ft (3.5 ft per dr bottom seal and 20 fastener clips for easy installation. Also includes instruction sheet. Made of top quality r
Front Door Vent Window Weatherstrips
p/n: 38-0029-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Windshield Gasket
p/n: 70-0601-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Windshield Weatherstrip - Vulcanized
p/n: 70-1534-50
This windshield weatherstrip mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. One hundred twenty (120") inch loop.
Rear Window Gasket
p/n: 60-0199-81
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Trunk Weatherstrip
p/n: 70-0083-85
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Motor mount service
p/n: 25-0062-11
Motor mount, upper front at cross member. One (1) per car. Revulcanization service only.Length: 4.75 inches. Width: 2.25 inches.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Rear bumper grommet
p/n: 70-0089-28
Grommets, rear bumper. Fully molded rubber. Four and one fourths inch (4-1/4") outside length by two and five sixteenths inch (2-5/16") outside width by one and eleven sixteenths inch (1-11/16") inside hole length by nine sixteenths inch (9/16") inside ho
Torque ball boot
p/n: 25-0034-24
Cushion, propeller shaft (drive shaft) bearing.Height: 1.0625 inches.
Fuel neck grommet
p/n: 70-0090-39
Grommet, fuel filler neck. Off center flange style. Fully molded rubber. Three and three fourths inch (3 3/4") outside width by three and seven eighths inch (3 7/8") outside length by two and three sixteenths inch (2 3/16") inside hole diameter by one an
Brown brake and clutch pad
p/n: 25-0024-89
Pads, brake and clutch pedal, authentic type ribbing, proper size, top quality rubber. Brown rubber. For black see our #25-0024-22.
Front Stablizer Bar End Link Kit
p/n: 70-0567-34
Kit, stabilizer bar link assembly. Twenty two (22) piece set for both sides of one (1) car, front and rear. (Order 2 sets if you need both). Hex head bolt. 5/16"-24nf x 7-5/8" lg. Comes with metal sleeve, cup washers and rubber grommets.
Front Spring Rubber Bumper
p/n: 70-0329-32
Front Spring Rubber Bumper - for upper control arm on frame.
Brake and clutch pedal pad
p/n: 25-0024-22
Pads, brake and clutch pedal, authentic type ribbing, proper size, top quality rubber. Black rubber. For brown see our #25-0024-89.Length: 3.125 inches.
Fuel neck grommet
p/n: 70-0091-39
Grommet, fuel filler neck. Saddle style. Three and three eighths inch (3 3/8") outside width by three and five eighths inch (3 5/8") outside length by two and one fourth inch (2 1/4") inside hole diameter by one and one fourth inch (1 1/4") height.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Brown seat back rest pad
p/n: 70-0482-89
Rest pads, seat back, outer, on two (2) door styles with folding seats. Brown rubber. For black see our #70-0482-88. Self retaining, perfect copy.
Rigid Run Channel
p/n: 70-0347-58
Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.
Windshield division bar gasket
p/n: 60-0039-51
Gasket set, windshield center post. Two (2) piece set for inner and outer, molded with holes and pilots.
Flexible Run Channel 6 Foot
p/n: 70-1239-58
Window run channel with stainless beaded edge. Six (6) foot length. Cloth covered, mohair lined, flexible channel for sides and top of door windows. Exact replacement for listed vehicles but can be used in many applications.
Beltline weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Folding seat bumper
p/n: 70-0482-88
Rest pads, seat back, outer, on two (2) door styles with folding seats. Black rubber. For brown see our #70-0482-89. Self retaining, perfect copy.
Vent division bar weatherstrip
p/n: 70-0791-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Front stabilizer bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber. One and one half inch (1 1/2") length by one and one half inch (1 1/2") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half in
Flexible Run Channel 5 Foot
p/n: 70-1238-58
Window run channel, stainless beaded edge. Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Perfect dimensions, Five eighths (5/8) inch wide by nine sixteenths (9/16) inch overall height, exact replacement. Five (5) fo
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
Weatherstrip, inner and outer for sliding quarter window, chrome beaded, mohair faced, flexible stock. May be formed to required outline. Six (6) foot strip.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Front suspension bumper
p/n: 50-0092-32
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Fender welting 3/16 bead 25ft
p/n: 70-1099-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Steel sash channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Starter pedal pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Windshield division bar gasket
p/n: 70-0098-52
Gasket, divided windshield center post. Combines inner and outer gasket in one piece as original. Seventeen (17) inch to (20) inch lengths.Length: 20.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Firewall grommet
p/n: 70-1877-20
Grommet, firewall. May be used on throttle, choke, oil gauge and others as needed. Up to six (6) required per vehicle.
Door check link rod end stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Rear stabilizer bushing
p/n: 70-0905-33
Bushing, rear stabilizer ends. Four (4) required per car. Fully molded rubber. One and one eighths inch (1 1/8") top outside diameter by seven eighths inch (7/8") bottom outside diameter by nine sixteenths inch (9/16") inside hole diameter by one and one
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Fabric hood lacing
p/n: 60-0578-42
Lacing, hood, fabric, webbing anti-squeak. With hollow center to receive wire if needed, or fasten with rivets if so found originally. Excellent quality. Seven eighths (7/8) inch by one eighths (1/8) inch thick.
Fabric hood lacing
p/n: 70-2221-42
Lacing, hood, fabric, webbing anti-squeak. DOES NOT have hollow center. Fasten with rivets if so found originally. Excellent quality.
Door bumper
p/n: 34-0025-42
Bumper, front and rear body hinge pillar, one (1) inch diameter by one fourth (1/4) inch thick, held by screw, steel core. Auxiliary, used only where needed to prevent door rattle.Note: also used on 1942-50 Packards with Clipper styling near t
Door bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Brown door lock knob
p/n: 70-0660-70
Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Steering knuckle support seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Brown door lock knob
p/n: 70-0354-70
Knob for inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. See also our #70-0660-70.
Shock and stabilizer grommet
p/n: 70-0274-33
Grommet, shock and stabilizer link. Eight (8) required per car. Fully molded rubber with locating collar. One and one sixteenth inch (1 1/16") outside diameter by nine sixteenths inch (9/16") locating collar outside diameter by three eighths inch (3/8") i
Door check link rod end stop
p/n: 70-0325-70
Pad, door check link. For rod type door check. One (1) inch diameter by three eighths (3/8) inch thick with five sixteenths (5/16) inch hole.
Peel-N-Stick Door Edge Weatherstrip
p/n: 70-0390-WT
Door edge weatherstrip made from high quality EPDM sponge rubber. 3M Peel-N-Stick backing provides superior adhesion for reliable performance. Makes for an easier installation of door weatherstripping. Also excellent for use in many different applications and on many different vehicle models.
Brake cable anti-rub cover
p/n: 70-1701-24
Anti-rub cover, brake cable. Fits all models with seven sixteenths (7/16) inch outside diameter cable.Width: 2.0 inches.
Door Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 70-0411-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Pressure ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel.Width: .375 inches. Height: .6875 inches.
Door Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 70-0390-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Body hole plug
p/n: 35-0863-45
Plug, body sheet metal holes. Used in various places (like trunks). For one and one half (1-1/2) inch hole in body.
Peel-N-Stick Door Weatherstrip
p/n: 70-0331-WT
Door edge weatherstrip made from high quality EPDM sponge rubber. 3M Peel-N-Stick backing provides superior adhesion for reliable performance. Makes for an easier installation of door weatherstripping. Also excellent for use in many different applications and on many different vehicle models.
Windshield Weatherstrip
p/n: 70-1190-52
Channel, windshield, for windows without chrome reveal molding. (With 2 piece windshield, select gasket for division bar).
Channel filler weatherstrip
p/n: 70-0489-58
Weatherstrip, channel filler, door window sash channel and some quarter window sash channel. Special type with wide weatherstrip edge to be trimmed at assembly, when necessary.
Door weatherstrip
p/n: 70-0066-73
Seal, door bottom, held by metal track or by clips. (See our # 70-0391-73 for clips). 2 door styles need about seven (7) foot per car.
Channel filler weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel.Width: .375 inches. Height: .
Door Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 70-0331-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Peel-N-Stick Door Weatherstrip
p/n: 70-0145-WT
Door edge weatherstrip made from high quality EPDM sponge rubber. 3M Peel-N-Stick backing provides superior adhesion for reliable performance. Excellent for use in many different applications and on many different vehicle models.
Door Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 70-0145-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Sash channel filler 1/16 cork
p/n: 70-1115-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Sash Channel Filler 1/16 Rubber
p/n: 70-2170-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Sash channel filler 1/32 cork
p/n: 70-1114-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition
Sash Channel Filler 1/32 Rubber
p/n: 70-2169-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.
Side window weatherstrip
p/n: 70-0079-58
Weatherstrip, side window lower edge, retained in metal flap on side of carrier channel, seals out water when window is cranked up.Width: .375 inches.
Hood bumper
p/n: 70-0294-42
Bumper, hood rest, cap type for adjustable screw, fifteenth sixteenths (15/16) inch, seven sixteenths (7/16) inch thick.
Hood bumper
p/n: 33-0031-42
Bumper, hood, self-retaining, along edge of hood against fender. One half (1/2) inch outside diameter, for five sixteenths (5/16) inch hole in sheet metal.
Door weatherstrip fastener
p/n: 70-0303-73
Metal clip for attaching door edge weatherstrip, our #70-0411-73. For one fourth (1/4) inch holes. Doors usually require one (1) clip per every six (6) inches. Estimate needs accordingly.
Shock Absorber Arm Bushing
p/n: 60-0216-33
Bushing, for double acting shock absorber arm link. Height: .78125 inches.
Trunk or hood bumper
p/n: 34-0203-42
Bumper, trunk or hood. Molded with clearance for screw. Used for: Buick 1942-50 Bumper for trunk. Chevrolet 1949-55 Bumper for rear hood corners on cowl. Chevrolet 1949-50 Bumper for trunk. Oldsmobile 1938 Bumper under hood corner on radi
Window channel retaining clip
p/n: 70-0514-62
Clip, side window run channel retaining. Rust resistant spring steel. Compare with your original.Width: .4375 inches. Height: .9375 inches.
Window channel retaining clip
p/n: 70-0515-62
Clip, side window run channel retaining. Rust resistant spring steel.Width: .4375 inches. Height: .8125 inches.
Door weatherstrip fastener
p/n: 70-0391-73
Clip, door bottom weatherstrip retaining, for our #70-0066-73 lower door weatherstrip, to fit one fourth (1/4) inch holes. Doors usually require one clip per every six (6) inches. Estimate needs accordingly.
Chrome molding washer
p/n: 60-0727-45
Washer, for attaching chrome moldings on body. Fits into metal cup retainer. Three fourths (3/4) inch diameter, use as required.