Body Weatherstrip Kit
This twenty-three (23) piece Body Weatherstrip Kit includes the major weatherstrip components needed for the body of your classic convertible model. We’ve put everything together in one simple and convenient kit.
Convertible Roof Rail Weatherstrip
This Convertible Roof Rail Weatherstrip fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
Front Door Vent Window Set
This six (6) piece Front Door Vent Window Set contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Weatherstrip Set
This seven (7) piece Front Door Weatherstrip Set is the primary seal for the doors to the body. The set includes the door bottom weatherstrip with molded corners, hinge pillar bellows, front edge seals, and rear edge seals.
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Front Bow Weatherstrip
Weatherstrip for windshield header, lower or rear, to folding top front roof bow. Installs on the windshield frame. Length: 50.25 inches.
Front Door Vent Window Weatherstrips
This Front Door Vent Window Weatherstrips contain the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
This Windshield Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends.
This Trunk Weatherstrip is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Weatherstrip, door bottom and corners, molded right and left. Overall length forty and three fourths (40-3/4) inch per door.
Hinge Pillar Weatherstrip
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Spring seat service
Seat, rear spring. Revulcanization service only. Send in complete casting with metal sleeve bushing.
Rear spring bumper service
Bumpers, rear springs to frame. Revulcanization service only.Length: 3.0 inches. Width: 2.5 inches.
Engine Mount Service – Revulcanization Only
This Revulcanization Service Only is designed to restore your Side Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Fender welting 1/4" bead 50ft
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 50ft chrome
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting with 3/16 Bead - 50 Ft. Roll
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Weatherstrip body hinge pillar
Weatherstrip body hinge pillar
Weatherstrip, front door opening. Right and left, hinge pillar at beltline. Constructed of soft rubber.Length: 12.0 inches.
Trunk Weatherstrip Corners
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Taillight mounting pad
Pad, taillight body mounting. Three (3) inch by six and one half (6-1/2) inch overall. Proper lip design.Length: 6.50 inches. Width: 3.0 inches.
Convertible Top Rest Block
Bumper, folding top rear bow (in top compartment). Two (2) required per car. Brass core as original.
Steering column floorplate
Cover (grommet), steering gear-to-toe board seal.Width: 5.8125 inches. Height: 6.0 inches.
Bumper, door side. Square type held by four (4) screws, metal core as original.
Fender Skirt Edge Weatherstrip
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Exhaust system support pad
Insulator (support), exhaust system, right angle type, fabric reinforced. Steel core at one end as original.Width: 2.5 inches. Height: 1.625 inches.
Roof Rail Filler
Filler, folding top front roof rail to side roof rail.
Brake and Clutch Pedal Pads
This reproduction Brake and Clutch Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads.
Front Spring Rubber Bumper
Front Spring Rubber Bumper Pair - for upper control arm on frame.
Brake Master Cylinder Filler Access Hole Cover
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Hood to Cowl Weatherstrip
This Hood to Cowl Weatherstrip is designed from original parts so it fits correctly. The pair comes ready to install with pre-punched holes.
License light mounting pad
Pad. rear license light mounting. Two and three fourths (2-3/4) inch by three and nine thirty seconds (3-9/32) inch overall. Two (2) required per vehicle.
Front Bow Weatherstrip
Weatherstrip, front bow to windshield, outer. Installs on convertible top. Approximately four (4) foot ten (10) inches long.
Headlight Door To Lens Seal
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Rigid Run Channel
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Window Felt Beltline Weatherstrips
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Vent division bar weatherstrip
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Bumper support bar pad
Pads, rear bumper bar, inner, to quarter panel. Fully molded rubber. Two and eleven sixteenths inch (2-11/16") outside length by one inch (1") outside width by one and five eighths inch (1-5/8") inside hole length by one fourth inch (1/4") inside hole wid
Inner Fender Seal
Inner Fender Seal for anti-rattle, running board apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Rear spring bushing
Bushing, rear spring front eye, inlox cartridge type as original.
Fender welting 1/4" bead 25ft
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Sliding Quarter Window Weatherstrip
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft lengths.
Spring seat seal
Seal, rear spring seat. Four (4) piece set.Height: .1875 inches.
Fender Skirt Edge Weatherstrip
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Front suspension bumper
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Fender Welting with 3/16 Bead - 25 Ft. Roll
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Front Stabilizer Bushing
Front Stabilizer Bushing - Front stabilizer bar mounting. Fully molded rubber. Two (2) required per car. One and five sixteenths inch (1 5/16") length by one and five sixteenths inch (1 5/16") width by five eighths inch (5/8") inside hole diameter by one and three fourths inch (1 3/4") height.
Headlight Mounting Pad
Headlight body mounting gasket. Rubber.
Rear Bumper Gravel Shield
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. Fully molded rubber with all original features.