Please click on the part name in red in order to get a complete description.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has molded sections for the wiper transmissions and the slot to accommodate the outer edge's decorative molding.
This ten (10) piece kit includes the inner and outer windowfelts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models with vent windows in the door.
Front motor mount cushion. Revulcanization service only. Send in cores and allow three weeks for service. Include inner core
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Scoop, air intake at front end sheet metal.
Weatherstrip, front door bottom. High quality weatherstrip with molded right and left hand ends.
Weatherstrip, door bottom (1951-2nd type). Molded left and right, overall length forty (40) inches.
Weatherstrip, front door. Includes molded end and extruded strip from inner end to bottom edge. With brass screw retainer as original.Length: 98.0 inches.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Engine harmonic balancer. Revulcanization service only. Send in your old, rebuildable balancer and pulley assembly.
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Cushion support, motor, rear on transmission to cross member. Revulcanization service only. Similar to #70-0674-11.Length: 3.75 inches. Width: 2.25 inches.
Cushion, motor support, rear on transmission to cross member. Revulcanization service only.
This trunk weatherstrip set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Kit, front stabilizer bar link assembly replacement. Twenty two (22) piece set for both sides of one (1) car. Hex head bolt. 3/8"-16nc x 8-7/8" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Bumpers, front spring. Lower arm, original copy, integral molded plate and stud, three eighths (3/8) inch standard thread, for installing.
Gasket set, rear and back up light installation. Sold in ten (10) piece set only. (A) Gasket, rear light body. twenty two (22) inches overall.
Run channel, front door window, for full length of division bar (approximately twenty nine (29) inches). Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top.
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Weatherstrip, body hinge pillar to door, bellows type of seal. One thirty seconds (1/32) inch thick. Die cut to exact outline.Length: 29.50 inches.
Seal, fender skirt edge.Length: 60.0 inches. Width: .625 inches.
Weatherstrip, rear door lower hinge pillar.Length: 16.0 inches.
Bumper, front spring, upper arm (on frame).
Pad, accelerator pedal. Brown rubber. For black see our #70-0208-40. Made to slip over old metal core after removing old rubber.
Bottoming pads, rear axle. Rubber block mounts by bracket to rear axle tube.
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Weatherstrip, hood to cowl. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay directly to the body.
Weatherstrip, sliding quarter window. Mounted vertically in body where leading edge of sliding window fits when closed. Right & left rubber only.
Grommets, rear door vent divider post (wind deflector), upper and lower, right and left. Four (4) piece set.
Pads, brake and clutch pedals. Brown rubber. For black see our #70-0176-22.Color:brown Length: 3.8125 inches.
Pad, accelerator pedal. Black rubber. For brown see our #70-0208-89. Made to slip over old metal core after removing old rubber.Length: 8.25 inches.
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Bulb type seal, gravel shield-to-rear bumper, anti-squeak. Also used as a door weatherstrip for some makes and models. Twelve (12) foot strip.
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.
Window run channel with stainless beaded edge. Six (6) foot length. Cloth covered, mohair lined, flexible channel for sides and top of door windows. Exact replacement for listed vehicles but can be used in many applications.
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Pads, brake and clutch pedals. Black rubber. For brown see our #70-0176-89.
Headlight door to lens seal. Molded without wire. Single lip type for sealed beams.
Grommet, steering column at floor, fits chrome ring.
Gasket, fog light body to ring or bezel.
Gasket, fog light lens to reflector.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Conduit, hydraulic line & power window wire. Front doors only. 2 pieces cut nine and one half (9-1/2) inches.Length: 9.50 inches. Height: 1.50 inches.
Window run channel, stainless beaded edge. Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Perfect dimensions, Five eighths (5/8) inch wide by nine sixteenths (9/16) inch overall height, exact replacement. Five (5) fo
Weatherstrip, front door opening, front body hinge pillar, lower. Extruded sponge to original configuration. Two (2) required per car.Width: .875 inches.
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Headlight body mounting gasket. Rubber.
Filler, splash apron. Die cut masticated rubber. Includes all factory style holes required for installation. Two (2) piece set.
Grommets, brake and clutch pedal shank below floorboard.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Insulator, steering column lower mounting frame gasket. Triangular shape with mounting holes and column tube clearance.
Grommet, used for windshield washer, vacuum lines, antenna lead, and others through firewall.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining, one half (1/2) inch deep by one half (1/2) inch wide, fifteen (15) inches long.
Insulator (hanger) tailpipe to frame. See also our #70-0600-13.Length: 3.9375 inches. Width: 1.9375 inches.
Grommet, brake and clutch pedal shank above floorboard. Special offset pattern as original.
Gasket, license light lens. One (1) per car.
Seal, lower suspension arm, inner. Four (4) piece set.
Insulator, exhaust system, muffler pipe bracket. Also intermediate pipe bracket on extra-long body styles. Two (2) required per car, most models.
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Mounting pad, vacuum operated fender mounted antenna with one and one half (1-1/2) inch base.
Bushing, rear spring shackle, upper. Four (4) required per car.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Mounting bracket and pad, for hydraulic pump. Number used as required.Length: 1.75 inches. Width: .8125 inches.
Grommet, taillight wiring.
Grommet, firewall, parking brake cable, has three eighths (3/8) inch angular hole through one and one fourth (1-1/4) inch diameter grommet.
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required. (See sketch and our #33-0540-62).
Grommet, glove box link.Width: .625 inches.
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Pad, body mounting. Fully molded rubber with locating collar. Rectangular shaped. Three inches (3") length by two inches (2") width by fifteen sixteenths inch (15/16") locating collar outside diameter by one half inch (1/2") inside hole diameter. Three ei
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Gasket, parking light lens and backup light lens. Die cut from one eighth (1/8) inch rubber.
Grommet, dimmer switch for carpet application.
Gasket, outside door handle. Four (4) piece set. Enough for two (2) doors.
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Pad, body mounting. Fully molded rubber with locating collar. Two inch (2") square by thirteen sixteenths inch (13/16") locating collar outside diameter by one half inch (1/2") locating collar inside diameter. Three eights inch (3/8") square base height b
Bumper, hood side to fender. Four (4) per car.
Bumper assembly, seven eighths (7/8) inch diameter by three eighths (3/8) inch bumper on 1/4-20 stud.Height: 1.50 inches.
Bushing, rear spring and shackle, lower. Requires 8 per car.
Bushing, lower shift levers and adjustable eye. Includes metal tube bearing. Used on transmission shifter rods.
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Dust cover, tie rod ends.
Cushion, body bolts under washer below bracket. Fully molded rubber. One and one half inch (1 1/2") inch outside diameter by seventeen thirty seconds inch (17/32") inside hole diameter by one fourth inch (1/4") height.
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.
Trunk weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Liner, mohair. Liner with a rubber backing. Apply with adhesive to division bars and channels. Helps reline guide bars on lock side of hardtops and convertibles.
This weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. The seal is structured to be applied to the body of the car.
Weatherstrip, door edge. Fine grain sponge. Larger type used on most GM cars this period. Width: 13/16". Height: 11/16".
Grommet, shock and stabilizer link. Eight (8) required per car. Fully molded rubber with locating collar. One and one sixteenth inch (1 1/16") outside diameter by nine sixteenths inch (9/16") locating collar outside diameter by three eighths inch (3/8") i
Trunk weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Gasket, trunk lock cylinder. Steel rule die cut from one thirty seconds (1/32) inch dense rubber.Length: 1.75 inches. Width: 1.25 inches. Height: .
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.