Search Results
Front Door weatherstrip
p/n: 90-0118-72
Door edge weatherstrip (1951-1st type). This part is the primary door to body weatherstrip. This kit includes the seals for the top and sides, the bottom of the door with molded ends and the bellows seal. Adhesive is not included in the kit.
Front Door weatherstrip
p/n: 90-0114-72
Front door edge weatherstrip (1951-2nd type). This part is the primary door to body weatherstrip. Includes the door seal for the sides and top, one pair of bellow seal, one pair of front lower body hinge pillar seal. And the bottom seal with molded ends.
Rear Window Gasket
p/n: 70-2524-81
This rear window gasket mounts around the full perimeter of the back glass and has the divider bars molded directly into it. It has properly molded corners to precisely conform to the glass and has the slot to accommodate the outer edge's decorative molding.
Windshield Gasket
p/n: 70-0512-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has molded sections for the wiper transmissions and the slot to accommodate the outer edge's decorative molding.
Side Window Run Channel Kit
p/n: 90-0141-58
This ten (10) piece kit includes the inner and outer windowfelts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Rear Door weatherstrip
p/n: 90-0119-72
Door edge weatherstrip. This part is the primary door to body weatherstrip. Includes the lower hinge pillar weatherstrip.
Front Door Vent Window Set
p/n: 90-0458-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Door weatherstrip
p/n: 70-0948-73
Weatherstrip, front door bottom. High quality weatherstrip with molded right and left hand ends.
Front Door Vent Window Weatherstrips
p/n: 38-0046-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Door weatherstrip
p/n: 70-0550-73
Weatherstrip, door bottom (1951-2nd type). Molded left and right, overall length forty (40) inches.
Door weatherstrip
p/n: 70-0738-73
Weatherstrip, front door. Includes molded end and extruded strip from inner end to bottom edge. With brass screw retainer as original.Length: 98.0 inches.
Motor mount service
p/n: 25-0072-11
Insulator, cushion assembly. Engine mount at bell housing, right and left. Revulcanization service only.Length: 5.25 inches.
Trunk Weatherstrip
p/n: 70-1039-84
This trunk weatherstrip set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Trunk Weatherstrip
p/n: 70-0870-84
This trunk weatherstrip set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Trunk Weatherstrip
p/n: 70-0871-84
This trunk weatherstrip set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Engine Mount Revulcanization Service Only
p/n: 25-0077-11
This Revulcanization Service Only is to restore your Front Lower Engine Support to it's like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine (Motor) Mount Revulcanization Service Only
p/n: 25-0062-11
This Revulcanization Service Only is to restore your supplied Front Upper Engine Mount at Crossmember to it's like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Door weatherstrip
p/n: 70-0668-73
Weatherstrip, body hinge pillar to door, bellows type of seal. One thirty seconds (1/32) inch thick. Die cut to exact outline.Length: 29.50 inches.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Hood To Cowl Weatherstrip
p/n: 70-0940-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Division bar grommet
p/n: 70-0483-62
Grommets, rear door vent divider post (wind deflector), upper and lower, right and left. Four (4) piece set.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Front Spring Rubber Bumper
p/n: 70-0329-32
Front Spring Rubber Bumper - for upper control arm on frame.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Flexible Run Channel
p/n: 70-1239-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Beltline Weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Vent division bar weatherstrip
p/n: 60-0569-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Gearshift boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Headlight Door To Lens Seal
p/n: 70-0389-14
Headlight door to lens seal. Molded without wire. Single lip type for sealed beams.
Front stabilizer bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber. One and one half inch (1 1/2") length by one and one half inch (1 1/2") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half in
Door conduit
p/n: 70-0828-21
Conduit, hydraulic line & power window wire. Front doors only. 2 pieces cut nine and one half (9-1/2) inches.Length: 9.50 inches. Height: 1.50 inches.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Fenderskirt Edge Seal
p/n: 60-0109-45
Fenderskirt Edge Seal - One (1) ten (10) foot strip. Length: 120.0 inches.
Door weatherstrip
p/n: 50-0219-73
Weatherstrip, front door opening, front body hinge pillar, lower. Extruded sponge to original configuration. Two (2) required per car.Width: .875 inches.
Front suspension bumper
p/n: 50-0092-32
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Side Window Sash Channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Rigid Run Channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Body mounting pad
p/n: 27-0092-48
Insulator, body mounting pad. Metal core & locating collar covered with rubber. Two inch (2") square by fifteen sixteenths inch (15/16") locating collar outside diameter by five eighths inch (5/8") locating collar inside hole diameter. Seven sixteenths in
Body mounting pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar. One and seven eighths inch (1 7/8") outside diameter by one and one eighths inch (1 1/8") locating collar outside diameter by three fourths inch (3/4") locating collar inside diame
Hydraulic pump mounting pad
p/n: 70-0852-67
Pad, mounting, hydraulic pump. Used on models with hydraulic window lifts or hydraulic convertible top. Two (2) to three (3) required. per car.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Solenoid plunger boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Wiring grommet
p/n: 70-0355-14
Grommet, electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fits seven eighths (7/8) inch hole in light body. Two (2) to eight (8) per car as required.