This kit includes the weatherstrip components needed for the glass on your restoration project.
This twenty-eight (28) piece Body Mounting Pad set is designed from the original parts for superior fitment and function. Designed from original parts, made from rubber with steel core.
This ten (10) piece Window Felt and Run Channel set includes the inner and outer window felts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Fitted gasket provides a formed, seamless seal.
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This Front Door Weatherstrip pair is high quality sponge rubber with inserted nylon clips. Designed from the original part for superior fitment and seal. Each strip is approximately one hundred sixty six (166") inches long.
This Windshield Gasket is designed from the original part for superior fitment and seal. It has the slot to accommodate the outer edge's decorative molding.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This Automatic Transmission Mount pair supports the transmission and dampens vibration. Engineered and designed to OE standards. Steel core as original.
Seal, rear wheelhouse panel-to-quarter panel, outer. Two (2) five (5) foot strips, one for each side.Length: 60.0 inches. Width: .21875 inches.
This Clipped Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter and directly to the trunk lid using properly spaced plastic clips.
This six (6) piece Door Auxiliary Weatherstrip set is designed from the original part for superior fitment and seal. The Auxiliary Weatherstrip, also known as a "J" seal, installs on the door front at the beltline, right and left sides of the vehicle.
Brake and Clutch Pedal Pads - The proper design and fully detailed with ribs extending down over sides of the pad. Length: 3.50 inches. Width: 2.0 inches.
This fourteen (14) piece Body Bumper Kit is designed from the original part for superior fitment, finish and function. Designed from originals and made from top quality rubber to ensure durability.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). This part is compatible to several Chevrolet model vehicles. Self-retaining, top quality. Height: 1.75 inches.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Accelerator Pedal Pad - Slip-over type made from top quality rubber. Length: 8.875 inches.
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Inner Fender Seal for anti-rattle, running board apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft lengths.
Front Stabilizer Bushing - Front stabilizer bar mounting. Fully molded rubber. Two (2) required per car. One and five sixteenths inch (1 5/16") length by one and five sixteenths inch (1 5/16") width by five eighths inch (5/8") inside hole diameter by one and three fourths inch (1 3/4") height.
Headlight body mounting gasket. Rubber.
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrips fits between the removable fender skirt and the rear fender quarter panel.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. This seal is the exact profile as original.
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Pad and steel bushing assembly. Two (2) required per vehicle Rectangular rubber with metal core, locating collar and metal bolt. Two and seven sixteenths inch (2 7/16") length by one and three fourths inch (1 3/4") width by three fourths inch (3/4") ins
Bumper, front suspension, lower arm. Steel core as original, excellent quality.
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
This black rubber Battery Clamp Cover helps to protect the nearby metal and finish. Good copy from an original part. Length: 3-1/2" inches.
Pad, body mounting. Rubber original type with metal core, locating collar and metal bolt liner. Two and one eighths inch (2 1/8") outside diameter by three fourths inch (3/4") inside bolt hole diameter by seven eighths inch (7/8") metal bolt outside diame
This Hood to Cowl Weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. The strip is designed from the original part for superior fitment and complete coverage.
Seals, under taillight assembly. Die cut masticated rubber to authentic original dimensions.
Grommet, cowl gutter drain hose. Nine sixteenth (9/16) inch hole through cowl side wall, five sixteenths (5/16) inch inside diameter. Two (2) per car.
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
This part is used as a front window regulator or accelerator rod through toe board seal. A front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
This Exhaust Tailpipe Hanger Strap is made from high-quality rubber for a precise, factory like fit for your classic vehicle. Muffler/tailpipe system, reproduction strap type is manufactured to OEM specifications.
This Hood to Fender Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle, order as needed.
This two (2) piece Splash Apron / A-Arm Dust Shield Set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Steele Rubber Products offers the best quality Dimmer Switch Grommet for your classic vehicle. This universal fit dimmer switch grommet is used during carpet installations in automotive restorations. Includes a wide flange for floor dimmer switch fitments.
Bushing, gearshift shaft lever, larger type. Three eighths (3/8) inch inside diameter by nine sixteenths (9/16) inch outside diameter barrel.Height: .
This Masticated Rubber Sheet is three thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Grommet, electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fits seven eighths (7/8) inch hole in light body. Two (2) to eight (8) per car as required.
This Trunk Floor Pan Plug is designed from the original part for superior fitment and seal. This plug is made from high quality EPDM dense rubber to provide excellent durability.