Window Felt and Run Channel Set
p/n: 90-0140-58
This eight (8) piece Window Felt and Run Channel set includes the inner and outer window felts, upper rigid run channels, and flexible run channels needed to complete two doors. The set can be used for front or rear doors in models with vent windows in the door.
Rear Quarter Vent Window Weatherstrips
p/n: 38-0058-76
This Rear Quarter Vent Window Weatherstrip pair is a four (4) piece pair. Fits both driver (Left) and passenger (Right) rear doors of the vent / wing window assemblies.
Engine Mount Service – Revulcanization Only
p/n: 25-0056-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Front Door Weatherstrip Set
p/n: 90-0100-72
This Front Door Weatherstrip Set is the primary weatherstrip for the door to vehicle body. Set includes the door perimeter weatherstrip and the door bottom weatherstrip. Enough for two (2) doors. Includes fasteners.
Rear Door Weatherstrip Set
p/n: 90-0101-72
This Rear Door Weatherstrip Set is designed from the original part for superior fitment and seal. These primary door weatherstrips mount (glue-on) directly to the left and right rear doors sealing the full perimeter of the doors against the vehicle body when the door is closed.
Front Door Vent Window Set
p/n: 90-0373-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Window Felt and Run Channel Set
p/n: 90-0142-58
This six (6) piece Window Felt and Run Channel set includes the inner and outer window felts and the flexible run channels needed to complete two (2) doors. This set is used for front or rear doors in models without vent windows in the door.
Front Door Vent Window Weatherstrips
p/n: 38-0029-55
These Front Door Vent Window Weatherstrips are the main weatherstrips needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Windshield Gasket
p/n: 50-0250-50
This Windshield Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 50-0287-81
This Rear Window Gasket Set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Engine Mount Service – Revulcanization Only
p/n: 25-0077-11
This Revulcanization Service Only is designed to restore your Front Lower Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Trunk Weatherstrip
p/n: 70-0083-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Brown Accelerator Service
p/n: 25-0094-89
Accelerator pedal. Brown rubber. For black see our #25-0094-40. Revulcanization service only. Includes new rubber sockets at base and for pedal rod.
Engine Mount Service – Revulcanization Only
p/n: 25-0062-11
This Revulcanization Service Only is designed to restore your Front Upper Engine Mount at Crossmember to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Accelerator Pedal Service
p/n: 25-0094-40
Accelerator pedal. Black rubber. For brown see our #25-0094-89. Revulcanization service only. Includes new rubber sockets at base and for pedal rod.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Rear Bumper Grommet
p/n: 70-0164-29
Grommets, rear bumper. (Some cars have this type, some have our #70-0144-29, sold separately. They are both interchangeable and original). Fully molded rubber.
Rumble Seat Weatherstrip
p/n: 70-0282-85
This Rumble Seat Weatherstrip is designed from the original part for superior fitment and seal. The pieces are molded as left and right for the lower corners.
Windshield Division Bar Gasket
p/n: 70-0159-51
This inner and outer Windshield Division Bar Gasket acts as a retainer for the outer division bar chrome molding.
Torque Ball Boot
p/n: 25-0034-24
Cushion, propeller shaft (drive shaft) bearing.Height: 1.0625 inches.
Front Suspension Bumper
p/n: 50-0125-32
Bumper, front suspension, lower arm.Width: 2.625 inches. Height: 2.5625 inches.
Front Bumper Grommet
p/n: 25-0010-28
Grommet, front bumper, right and left. Hollow back, original copy. Length: 4.0625 inches.
Clutch and Brake Pedal Pads - BROWN
p/n: 25-0024-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Brown rubber.
Fuel Neck Grommet
p/n: 25-0013-41
Grommet, fuel filler neck. Virtually exact copy for two and one fourth (2-1/4) inch diameter filler neck through body or fender.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Front Spring Rubber Bumpers
p/n: 70-0329-32
This Front Spring Rubber Bumper Pair fits to the upper control arms on frame. Manufactured to OEM specifications to install for an authentic fit, finish and function.
Clutch and Brake Pedal Pads - BLACK
p/n: 25-0024-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Black rubber.
Brake and clutch shank seal
p/n: 25-0051-24
Seals, brake and clutch pedal shank-to-toe board, sponge rubber. Two (2) per car.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Vent Window Division Post Weatherstrips
p/n: 70-0791-56
This Front Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. These pieces mount on the vertical division post with tabs and seal as the vent glass closes against them. Fully molded with metal core.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Brown Gearshift Boot
p/n: 50-0035-89
Boot, gearshift. Brown rubber. For black see our #50-0035-24.Color:brown Width: 2.8125 inches.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Gearshift Boot
p/n: 50-0035-24
Boot, gearshift. Black rubber. For brown see our #50-0035-89.Width: 2.8125 inches.
Starter Pedal Pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Battery Carrier Edge Liner
p/n: 27-0091-21
Seal strip, battery to fender apron. Two (2) correct cross section strips nineteen (19) inches long.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Wiper Transmission Gasket
p/n: 70-1197-53
Gasket, windshield wiper transmission. Replaces #4074294 & #4082366.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Side Window Run Channel
p/n: 70-1169-58
Channel, side window, pre-flocked, 9/16" wide to accommodate metal frame side window. Available by the foot.
Door Check Link Rod End Stop Washer
p/n: 70-0384-70
A quality Door Check Link Rod End Stop Washer for door check mechanism. One and seven-sixteenths (1-7/16") inch diameter by three-sixteenths (3/16") inch thick.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Brown Door Lock Knob
p/n: 70-0354-70
This is the knob or button for the inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. The part fits many different vehicles.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Steering Knuckle Support Seal
p/n: 50-0199-35
This Steering Knuckle Support Seal is designed from the original part for an authentic fit, finish, and appearance. Fits at the steering knuckle support at the upper pivot pin. Four (4) required per car.
Door Check Link Rod End Stop
p/n: 70-0325-70
A quality Door Check Link Rod End Stop for rod type door check mechanism. One (1") inch diameter by three-eighths (3/8") inch thick with five-sixteenths (5/16") inch hole.
11/16" Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel. Available by the foot.
9/16" Door Edge Weatherstrip
p/n: 70-0411-73
This Door Edge Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Brake Cable Shielding Cover - 2 Inch
p/n: 70-1701-24
This two (2) inch long Brake Cable Shielding Cover is designed install for an authentic fit, finish and function. Fits all models with seven sixteenths (7/16) inch outside diameter cable.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
1/2" Door Bottom Weatherstrip
p/n: 70-0066-73
This Door Weatherstrip is designed for the bottom of the door and is held in by a metal track or by clips. Available by the foot.
11/16" Channel Filler Weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel. Available by the foot.
7/8" Window Weatherstrip
p/n: 70-1191-52
This Window Weatherstrip is for models without chrome reveal molding. Available by the foot.
7/8" Window Weatherstrip
p/n: 70-1192-52
This Window Weatherstrip is for models with chrome reveal molding. Available by the foot.
7/8" Windshield Weatherstrip
p/n: 70-1190-52
This Windshield Weatherstrip is for windows without chrome reveal molding. For a 2-piece windshield, select gasket for division bar. Available by the foot.
Side Window Bumper
p/n: 60-0195-62
Anti-rattle, side window, inner and outer. Fits slot in outer door body metal and inner window frame (garnish molding).
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
3/8" Side Window Weatherstrip
p/n: 70-0079-58
Weatherstrip, side window lower edge. Available by the foot.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
1/2" Hood Bumper
p/n: 33-0031-42
Self-retaining hood bumper, along edge of hood against fender. Up to twenty (20) per car.
Shock Absorber Link Arm Bushing
p/n: 60-0216-33
This Shock Absorber Link Arm Bushing is designed from the original part for superior fitment, finish and function. This bushing is for double acting shock absorber arm links.
Trunk or Hood Bumper
p/n: 34-0203-42
This Bumper is designed to be used for the trunk or hood. The bumper is molded with clearance for the screw.
1/2" Standard Bumper
p/n: 33-0136-42
This Standard Bumper is fully molded from quality dense rubber to provide excellent durability. Commonly used as a door bumper on the center upper post on post model vehicles.
Door Weatherstrip Fastener Clip
p/n: 70-0303-73
Metal Fastener clips, sold as an each, for attaching door edge weatherstrips. For one fourth (1/4) inch holes. Doors usually require one (1) clip per every six (6) inches.
Door Weatherstrip Fastener Retaining Clip
p/n: 70-0391-73
This Door Weatherstrip Retaining Clip is manufactured to OEM specifications to install for an authentic fit, finish and function. A direct-fit for Lower Door Weatherstrip 70-0066-73. Fits one-fourth (1/4") inch holes. Usually requires one clip per every six (6") inches.